1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. gayoub
    Post

    Solved Temp Fail Error

    Thanks guys I checked the wiring for the thermistor and heater core and it seems that something was loose. It printed fine after than. I will keep...
    Post by: gayoub, Mar 20, 2019 in forum: Troubleshooting
  2. gayoub
    Thread

    Solved Temp Fail Error

    Hi Guys I have a Robo3dR1 with the v6 hotend. It's been working fine for ages, but today for some reason, I keep getting a Temp Fail Error and the...
    Thread by: gayoub, Mar 20, 2019, 2 replies, in forum: Troubleshooting
  3. gayoub
    Post

    Solved Z steps

    Thanks Mark, that fixed the problem. You should be paid double :-) Regards George
    Post by: gayoub, Oct 24, 2017 in forum: Troubleshooting
  4. gayoub
    Post

    Solved Z steps

    Thanks for that, I will install the 8mm firmware.
    Post by: gayoub, Oct 24, 2017 in forum: Troubleshooting
  5. gayoub
    Thread

    Solved Z steps

    I've just installed an E3D v6 hotend, updated the firmware (Auto_Level_7_17_516inch) and printed a test cube. The X and Y seem fine, but the Z is...
    Thread by: gayoub, Oct 24, 2017, 4 replies, in forum: Troubleshooting
  6. gayoub
    Post

    Updating Firmware after E3D vs 6 upgrade

    Woohoo, there's life again :-) Controller and SD3 working. I will tweak them later, but thanks heaps. Regards George
    Post by: gayoub, Oct 23, 2017 in forum: General Questions
  7. gayoub
    Post

    Updating Firmware after E3D vs 6 upgrade

    Yes, I think I must've flashed the wrong firmware after the computer upgrade. I am trying to upload the Robo3d firmware now. Steep learning curve...
    Post by: gayoub, Oct 23, 2017 in forum: General Questions
  8. gayoub
    Post

    Updating Firmware after E3D vs 6 upgrade

    Thanks for your quick response.
    Post by: gayoub, Oct 23, 2017 in forum: General Questions
  9. gayoub
    Post

    Updating Firmware after E3D vs 6 upgrade

    I have a Smart LCD Controller. By the way, does anyone know where I can download the firmware for the Robo3dR1. I think I might do a clean instal....
    Post by: gayoub, Oct 23, 2017 in forum: General Questions
  10. gayoub
    Post

    Updating Firmware after E3D vs 6 upgrade

    OK I have updated the Arduino to the latest version Under tools I have chosen Arduino/Genuino Mega or Mega 2560 Chosen ATMega2560 (Mega 2560) But...
    Post by: gayoub, Oct 22, 2017 in forum: General Questions
  11. gayoub
    Thread

    Updating Firmware after E3D vs 6 upgrade

    Hi guys I have updated my Robo3D-1 to ED3 vs 6 and I changed the temperature setting #define HEATER_0_MAXTEMP 310 //Change this value only and...
    Thread by: gayoub, Oct 22, 2017, 12 replies, in forum: General Questions
  12. gayoub
    Post

    Solved M565 Z question

    No worries, I forgot it's not simply about me, but others are looking for answers as well. :-) Learning together.... George
    Post by: gayoub, Jan 28, 2016 in forum: General Questions
Showing results 1 to 12 of 12
Search Again