1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Solved after auto leveling printer stops, temp drops printer says done

Discussion in 'Troubleshooting' started by simonw, Jun 30, 2015.

  1. simonw

    simonw New Member

    Joined:
    Jun 17, 2015
    Messages:
    9
    Likes Received:
    1
    Any help would be greatly appreciated!
    i start a print job in matter-control. the bed and extruder heat up. the printer autoleves then stops in back right corner.
    temperature starts dropping immediately and a bar flies across the the top showing status of print job then says done.

    thanks in advance
     
    #1 simonw, Jun 30, 2015
  2. Taylor

    Taylor Member

    Joined:
    Mar 10, 2014
    Messages:
    109
    Likes Received:
    13
    Try printing another file,does it do the same? Post your GCODE here and lets see what it says.
     
    #2 Taylor, Jul 2, 2015
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    Try a different tool (not MatterControl). Repetier host and Cura are free. Try one of those.
     
    #3 mark tomlinson, Jul 3, 2015
  4. simonw

    simonw New Member

    Joined:
    Jun 17, 2015
    Messages:
    9
    Likes Received:
    1
    sorry for not responding sooner . was away for holiday weekend . will try tonight when i get home from work .
    once again thanks
     
    #4 simonw, Jul 6, 2015
  5. simonw

    simonw New Member

    Joined:
    Jun 17, 2015
    Messages:
    9
    Likes Received:
    1
    turns out thermister got loose on hot end. tightened and problem went away.
    thanks for all your help and suggestions
     
    #5 simonw, Jul 7, 2015
    Mike Kelly likes this.
  6. Anthony Freeman

    Anthony Freeman New Member

    Joined:
    Sep 3, 2015
    Messages:
    2
    Likes Received:
    0
    I'm having the same problem and it is not going away.
     
    #6 Anthony Freeman, Sep 3, 2015
  7. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    Did you do everything already suggested in this thread?

    Better off starting a new one.
     
    #7 mark tomlinson, Sep 4, 2015
  8. Anthony Freeman

    Anthony Freeman New Member

    Joined:
    Sep 3, 2015
    Messages:
    2
    Likes Received:
    0
    I solved the problem. It is a new printer and after checking the wiring I noticed almost every wire was loose and needed to be redone. Once I put new connectors on all the wiring it started working just fine.
     
    #8 Anthony Freeman, Sep 11, 2015
  9. Stemcreekside

    Stemcreekside New Member

    Joined:
    Nov 16, 2015
    Messages:
    7
    Likes Received:
    0
    <-T:42.5 E:0 B:92.2
     
    #9 Stemcreekside, Nov 20, 2015
  10. Stemcreekside

    Stemcreekside New Member

    Joined:
    Nov 16, 2015
    Messages:
    7
    Likes Received:
    0
    Then their are constant errors when it calibrates.
     
    #10 Stemcreekside, Nov 20, 2015
  11. Stemcreekside

    Stemcreekside New Member

    Joined:
    Nov 16, 2015
    Messages:
    7
    Likes Received:
    0
    or ->M105
    <-ok T:37.0/0.0 B:79.2/0.0 To:36.6 / 0.0 @:0 B@:0
     
    #11 Stemcreekside, Nov 20, 2015
  12. Stemcreekside

    Stemcreekside New Member

    Joined:
    Nov 16, 2015
    Messages:
    7
    Likes Received:
    0
    <-Error:Temperature heated bed switched off. MAXTEMP triggered !! [399.374]

    <-Error:printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) [399.379]

    <-ok [399.379]

    ->N2 M105*37 [399.381]

    <-ok [399.383]

    ->N3 G21*25 [399.384]

    <-ok [399.719]

    <-ok [399.719]

    ->N4 M107*33 [399.719]

    <-ok T:30.7 /0.0 B:110.0 /0.0 T0:30.7 /0.0 @:0 B@:0 [399.722]

    <-ok [399.722]

    <-ok [399.722]

    ->N5 M190 S110*109 [399.723]

    <-ok [399.772]

    ->N6 M104 T0 S240*33 [399.772]

    <-ok [399.775]

    ->N7 T0*61 [399.776]

    <-echo:Active Extruder: 0 [399.780]

    <-ok [399.780]

    ->N8 G28 X0 Y0 Z0*80 [399.782]

    <-ok [402.574]

    ->N9 M114*46 [402.575]

    <-X:0.00 Y:0.00 Z:-0.80 E:0.00 Count X: 0.00 Y:0.00 Z:-0.80 [402.582]

    <-ok [402.582]

    ->N10 M105*22 [402.582]

    <-ok T:30.9 /240.0 B:109.6 /0.0 T0:30.9 /240.0 @:127 B@:0 [402.590]

    ->N11 G1 Z5 F5000*52 [402.592]

    <-Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) [402.600]

    <-ok [402.600]
    this is what I got
     
    #12 Stemcreekside, Nov 20, 2015
  13. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    >
    <-Error:Temperature heated bed switched off. MAXTEMP triggered !! [399.374]

    You bed exceeded MAX TEMP as defined in the firmware (CONFIGURATION.H).

    If you know what version you are on, check the source for that version. I keep mine set at 115...
     
    #13 mark tomlinson, Nov 20, 2015
  14. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    Specifically look for this line:

    #define BED_MAXTEMP 110

    Whatever that number is, that is your bed limit. Some versions had this as low as 85.
     
    #14 mark tomlinson, Nov 20, 2015
  15. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    The differences had to do with the way they had the bed wired. So if you have the ribbon cable connecting your bed heater to the RAMPS, crank it up. Otherwise you may want to replace that wiring to use the ribbon cable approach first.
     
    #15 mark tomlinson, Nov 20, 2015

Share This Page