1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

bed crashes to nozzle always up after using z-offset wizard

Discussion in 'Troubleshooting' started by chn9292, Apr 12, 2020.

  1. chn9292

    chn9292 New Member

    Joined:
    Apr 12, 2020
    Messages:
    21
    Likes Received:
    1
    ı set z-offset value and after than click button to Z home. Bed always wants to go up. Non-Stop. It always damages nozzle. I have to shut it down and start to no damaging on nozzle.
     
    #1 chn9292, Apr 12, 2020
  2. tkoco

    tkoco - -.- --- -.-. ---
    Staff Member

    Joined:
    May 7, 2018
    Messages:
    721
    Likes Received:
    273
    Question: What are your software and firmware versions? Please read the R2 FAQ for further information.
     
    #2 tkoco, Apr 12, 2020
  3. chn9292

    chn9292 New Member

    Joined:
    Apr 12, 2020
    Messages:
    21
    Likes Received:
    1
    as ı remember , last version cause machine did not up to date itself. problem is bed always wants to up. when I click to raise , it goes down and non stop.
     
    #3 chn9292, Apr 12, 2020
  4. tkoco

    tkoco - -.- --- -.-. ---
    Staff Member

    Joined:
    May 7, 2018
    Messages:
    721
    Likes Received:
    273
    Please check the printer right after power up and let me know what version of RoboOS and version of Marlin firmware is currently in the printer.

    Without knowing what state your printer is in, there is little hope in troubleshooting the situation. Your description suggests a software problem. So let's verify it.
     
    #4 tkoco, Apr 12, 2020
    mark tomlinson likes this.
  5. chn9292

    chn9292 New Member

    Joined:
    Apr 12, 2020
    Messages:
    21
    Likes Received:
    1
    2,0,0-r2,6 and marlin is 1,1,6_roboversion_1,2,4_R2.hex
     
    #5 chn9292, Apr 14, 2020
  6. tkoco

    tkoco - -.- --- -.-. ---
    Staff Member

    Joined:
    May 7, 2018
    Messages:
    721
    Likes Received:
    273
    The firmware is old. I recommend upgrading to release Marlin 1,1,6_roboversion_1.2.6_R2.hex The link to the firmware is in the R2 FAQ along with instructions. While you can save out the firmware parameters, I recommend re-doing the calibrations as a bad parameter can torpedo your troubleshooting.
     
    #6 tkoco, Apr 14, 2020
    mark tomlinson likes this.
  7. chn9292

    chn9292 New Member

    Joined:
    Apr 12, 2020
    Messages:
    21
    Likes Received:
    1
    how can ı get lastest verison of it to upload via usb disk ? ı solved problem but now , there is no connection with wifi. it doesnt find any network
     
    #7 chn9292, Apr 17, 2020
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,914
    Likes Received:
    7,338
    #8 mark tomlinson, Apr 17, 2020
  9. chn9292

    chn9292 New Member

    Joined:
    Apr 12, 2020
    Messages:
    21
    Likes Received:
    1
    Thank you so much , i solved problem.
     
    #9 chn9292, Apr 17, 2020
    mark tomlinson likes this.

Share This Page