1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Unresolved Printer Stops after auto leveling

Discussion in 'Troubleshooting' started by Mindstar, May 22, 2016.

  1. Mindstar

    Mindstar New Member

    Joined:
    Apr 1, 2016
    Messages:
    7
    Likes Received:
    0
    Robo 3D Plus using Simplyfy I get the following error code after the machine completes the auto leveling process:

    RECEIVED: Bed x: 15.00 y: 20.00 z: -2.28

    RECEIVED: Bed x: 110.00 y: 20.00 z: -1.11

    RECEIVED: Bed x: 205.00 y: 20.00 z: -0.49

    RECEIVED: Bed x: 205.00 y: 125.00 z: -0.61

    RECEIVED: Bed x: 110.00 y: 125.00 z: -1.04

    RECEIVED: Bed x: 15.00 y: 125.00 z: -2.12

    RECEIVED: Bed x: 15.00 y: 230.00 z: -1.58

    RECEIVED: Bed x: 110.00 y: 230.00 z: -0.75

    RECEIVED: Bed x: 205.00 y: 230.00 z: -0.33

    RECEIVED: Eqn coefficients: a: 0.01 b: 0.00 d: -2.26

    RECEIVED: planeNormal x: -0.01 y: -0.00 z: 1.00

    RECEIVED: ok

    SENT: M105

    RECEIVED: echo:endstops hit: Z:-0.33

    endstops hit: Z:-0.33

    RECEIVED: Printer stopped due to errors. Fix the error and use M999 to restart.
     
    #1 Mindstar, May 22, 2016
  2. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Hi there can you upload your simplify fff and ill look through it. Somehow.i missed your post! Im very sorry for the long delay

    Screen shots will work too.
     
    #2 Geof, May 24, 2016
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    This " Printer stopped due to errors. Fix the error and use M999 to restart."

    Means an error occurred.
    You only posted a small portion of the GCode log and it doesn't have the actual error in it.
    Save the entire thing to disk and upload it.
     
    #3 mark tomlinson, May 24, 2016
    Geof likes this.
  4. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    im wondering if he doesnt have the wait for temp checked. Mine would autolevel then min temp error (not enough time in the autolevel to get to temp)
     
    #4 Geof, May 24, 2016
    mark tomlinson likes this.
  5. Mindstar

    Mindstar New Member

    Joined:
    Apr 1, 2016
    Messages:
    7
    Likes Received:
    0
    I'll have to wait for the error to occur again to get the complete error code. I think its not a drop in the temperature.
     
    #5 Mindstar, May 25, 2016
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    MINTEMP is the usual reason for this like @Geof says (because the thermistor gets loose or a bad connection to the themistor exists).

    What happens is it starts moving for the 9-points on the autolevel and then thermistor moves causing temperature to go down, but the printer will continue the 9-point measurement before looking at the temperature again.

    Get the actual error though and we can help you sort it out.
     
    #6 mark tomlinson, May 25, 2016
    Last edited: May 25, 2016
    Geof likes this.

Share This Page