1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Shoutbox Archive

Discussion in 'Archive' started by Harry, Mar 4, 2015.

  1. TaigaChat

    TaigaChat Guest

    Apr 5, 2019 at 11:02 AM - teknoprep: no matter what i do i can not get the z offset
    Apr 5, 2019 at 11:02 AM - teknoprep: m851 z-4
    Apr 5, 2019 at 11:02 AM - teknoprep: m500 .. then m503 .. shows the offset
    Apr 5, 2019 at 11:02 AM - teknoprep: doesn't adjust inital height of my prints
     
  2. TaigaChat

    TaigaChat Guest

    Apr 5, 2019 11:02 PM - tonycstech: Does anybody know R1 motor torque specs ?
     
  3. TaigaChat

    TaigaChat Guest

    Apr 7, 2019 8:49 AM - mark tomlinson: Probably 30-ish nm of torque. You cna find the same physical size with more torque -- most of the ones I use for replacement have at least 60nm
     
  4. TaigaChat

    TaigaChat Guest

    Apr 9, 2019 11:31 AM - Johannbv: My R2 is printing about 10mm in the air above the print bed. Did the Z-offset reset several times over and still does it. Can anyone help?
    Apr 9, 2019 11:36 AM - Geof: Have you cleaned the IR Sensor?
    Apr 9, 2019 11:36 AM - Geof: Sounds like its triggering false showing the bed before it actually gets there
    Apr 9, 2019 11:36 AM - Geof: may want to start up a trouble shooting thread in the R2 section
    Apr 9, 2019 11:49 AM - Johannbv: I just posted the in the trouble shooting. However, I was printing from Octoprint and when I switched to printing off a USB it prints correctly..
    Apr 9, 2019 12:21 PM - Geof: interesting. I'd assume either an octoprint issue or something in the start gcode in octoprint vs your slicer is wonky.
     
  5. TaigaChat

    TaigaChat Guest

    Apr 15, 2019 7:36 AM - teknoprep: hi all
    Apr 15, 2019 7:37 AM - teknoprep: i updated to the latest community post with UBL and all that... works great except i can not define a z offset that ever takes effect
    Apr 15, 2019 7:37 AM - teknoprep: i find that i need to raise my z 1.4mm higher than what UBL sets it to for the entire bed
    Apr 15, 2019 7:37 AM - teknoprep: does anyone have any idea what i could do to get this to take effect ?
    Apr 15, 2019 2:30 PM - mark tomlinson: Try a global Z offset in the slicer you are using
     
  6. TaigaChat

    TaigaChat Guest

    May 18, 2019 1:14 PM - Roger Worden: Is there a minimum nozzle size for the R1+ ? I got a near-instant jam with PLA at 0.2 and am wondering if there are any specified or practical limits.
     
  7. TaigaChat

    TaigaChat Guest

    May 19, 2019 8:20 AM - WheresWaldo: going from 0.4 to 0.2, you should at least halve the print speed, maybe even need to go as low as quarter the normal print speed.
     
  8. TaigaChat

    TaigaChat Guest

    May 29, 2019 11:28 AM - Dan: Anyone here?
    May 29, 2019 8:38 PM - albert3d: From time to time
     
  9. TaigaChat

    TaigaChat Guest

    May 31, 2019 at 11:00 AM - Cosmin Buidan: Just purchased a R1+, and after instalation my prints stop after 1-2 layers
    May 31, 2019 at 6:32 PM - albert3d: Might be a bad sd
     
  10. TaigaChat

    TaigaChat Guest

    Jun 2, 2019 5:33 PM - levoncio99: i upgraded to v6 everything then its gets clogged because tip came loose, tightend everything back up no getting MINTEMP error
    Jun 2, 2019 5:48 PM - levoncio99: throwing this thing in the trash with a brand new e3d hotend
    Jun 2, 2019 5:48 PM - levoncio99: buying another printer
    Jun 2, 2019 8:06 PM - BrooklynBay: Check the connection on the heating element & thermistor.
     

Share This Page