1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Solved This is what I get for being impatient (e3d v6 installation)

Discussion in 'Troubleshooting' started by Justin Riera, Nov 2, 2015.

Page 2 of 2
  1. janot928

    janot928 Active Member

    Joined:
    Feb 20, 2015
    Messages:
    276
    Likes Received:
    40
    Why?

    Envoyé de mon SM-G900F en utilisant Tapatalk
     
    #21 janot928, Nov 5, 2015
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    You can read the voltage/potential/tension across the solder points then. It has to connect to the RAMPS output somehow and that is what you need to check. If the RAMPS is working then the heater core is dead (or vice-versa)
     
    #22 mark tomlinson, Nov 5, 2015
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    If you mean the parts fan it is not always on. You can (in some slicers) force it on and see if it runs.
    If you mean the extruder fan then you still have a wiring problem.
     
    #23 mark tomlinson, Nov 5, 2015
  4. Justin Riera

    Justin Riera Member

    Joined:
    Oct 12, 2015
    Messages:
    57
    Likes Received:
    4
    Because like Mike said, on the r1+ D10 and 9 are switched. he was right.
     
    #24 Justin Riera, Nov 5, 2015
  5. Justin Riera

    Justin Riera Member

    Joined:
    Oct 12, 2015
    Messages:
    57
    Likes Received:
    4
    The parts fan. should i just wire it into the power supply and have it always running if soldering doesnt work?
     
    #25 Justin Riera, Nov 5, 2015
  6. Justin Riera

    Justin Riera Member

    Joined:
    Oct 12, 2015
    Messages:
    57
    Likes Received:
    4
    wait nevermind i just realized the parts fan has a jst connector. Where does that go into? also there is a cable that says LED A on my board with a jst connector. what is that for?
     
    #26 Justin Riera, Nov 5, 2015
  7. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,917
    Likes Received:
    7,338
    No. It is not supposed to always be on.
    The slicer needs to be able to control this.
     
    #27 mark tomlinson, Nov 5, 2015
  8. Justin Riera

    Justin Riera Member

    Joined:
    Oct 12, 2015
    Messages:
    57
    Likes Received:
    4
    Ok. my positive works but my negative doesnt.
     
    #28 Justin Riera, Nov 5, 2015
  9. Justin Riera

    Justin Riera Member

    Joined:
    Oct 12, 2015
    Messages:
    57
    Likes Received:
    4
    omg now my RAMPS doesnt work. Thanks guys but I'm just gonna order a new one
     
    #29 Justin Riera, Nov 5, 2015
Page 2 of 2

Share This Page