1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Wits end.

Discussion in 'Troubleshooting' started by Ricky_Spanish, Oct 3, 2014.

Thread Status:
Not open for further replies.
Page 3 of 3
  1. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    Lol Matt is littrtaly my favorite person.
    Hey I also noticed your site is running a little faster. Idk if you changed anything but it is loading like right away. Before it used to lagg a bit. Quite happy about this.
     
    #41 collin, Oct 9, 2014
  2. Printed Solid

    Printed Solid Volunteer Admin
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    1,605
    Likes Received:
    1,003
    Turned out pretty good.

    Yeah, Collin, they finally got sick of me submitting tech support tickets every day and reset the server. Everything got 'magically' better after that.

    hellskull.jpg
     
    #42 Printed Solid, Oct 9, 2014
    5 people like this.
  3. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    Goodness that turned out well. Is that the new bamboo fill?
     
    #43 collin, Oct 9, 2014
  4. Printed Solid

    Printed Solid Volunteer Admin
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    1,605
    Likes Received:
    1,003
    Standard woodfill 0.8mm nozzle on the Ultimaker.
    Haven't cracked open bamboo yet, but am probably going to try it first on the robo.
     
    #44 Printed Solid, Oct 9, 2014
    2 people like this.
  5. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    I really need to get a larger nozzle. I think I tacked on something about it with my xt invoice request.
     
    #45 collin, Oct 9, 2014
    2 people like this.
  6. Ricky_Spanish

    Ricky_Spanish Member

    Joined:
    Oct 3, 2014
    Messages:
    34
    Likes Received:
    24
    Got my hotend installed. Heated her up, ran the PID, everything was beautiful. Started a print, and 4 minutes in it stopped and I'm getting the "Unknown USB device" errors now and can't connect. There are no lights on on the board, just the SD reader and power supply. When I hit the reset, I get 2 flashes from the green LED. Mike Kelly, you help me with this one, I may hit that wish list for you. lol
     
    #46 Ricky_Spanish, Oct 17, 2014
  7. Printed Solid

    Printed Solid Volunteer Admin
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    1,605
    Likes Received:
    1,003
    have you gone through to check wire connections?
     
    #47 Printed Solid, Oct 17, 2014
    2 people like this.
  8. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    Yeah an unknown usb device error like that probably is a symptom of a shorted wire. Especially if it happens during motion.
     
    #48 Mike Kelly, Oct 17, 2014
    2 people like this.
  9. Ocsff

    Ocsff Active Member

    Joined:
    Oct 28, 2014
    Messages:
    135
    Likes Received:
    40
    Mike you are a wealth of knowledge. Thanks for all the posts
     
    #49 Ocsff, Oct 28, 2014
    2 people like this.
  10. Ricky_Spanish

    Ricky_Spanish Member

    Joined:
    Oct 3, 2014
    Messages:
    34
    Likes Received:
    24
    Board was fried. I replaced it tonight, and it's all good now.
     
    #50 Ricky_Spanish, Oct 28, 2014
    3 people like this.
Page 3 of 3
Thread Status:
Not open for further replies.

Share This Page