1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by DJ Sterrett

  1. DJ Sterrett
    Post

    Solved Extruder motor grinding on retraction only...extrudes correctly

    Just for proof i'm not full of it...there was no other damage. I picked it up and tossed it out the front door. Like i said im glad i was...
    Post by: DJ Sterrett, Jan 26, 2020 in forum: Troubleshooting
  2. DJ Sterrett
    Post

    Solved Extruder motor grinding on retraction only...extrudes correctly

    Its a moot question... the printer just went up in flames :( at least i was watching it when it happened.
    Post by: DJ Sterrett, Jan 26, 2020 in forum: Troubleshooting
  3. DJ Sterrett
    Post

    Solved Extruder motor grinding on retraction only...extrudes correctly

    So here is what i have tried. 1. Bump up the voltage .1v...still grinding 2. Swap the extruder and another driver...still grinding. All i can...
    Post by: DJ Sterrett, Jan 26, 2020 in forum: Troubleshooting
  4. DJ Sterrett
    Post

    Solved Extruder motor grinding on retraction only...extrudes correctly

    Mark you suggested bumping up the voltage on the driver a little i believe...what should that voltage read on a multimeter?
    Post by: DJ Sterrett, Jan 26, 2020 in forum: Troubleshooting
  5. DJ Sterrett
    Post

    Solved Extruder motor grinding on retraction only...extrudes correctly

    What motor and driver do you recommend?
    Post by: DJ Sterrett, Jan 25, 2020 in forum: Troubleshooting
  6. DJ Sterrett
    Thread

    Solved Extruder motor grinding on retraction only...extrudes correctly

    As the title says...i have an old machine that extrudes fine and i can get decent prints but every now and then on retraction the extruder motor...
    Thread by: DJ Sterrett, Jan 25, 2020, 12 replies, in forum: Troubleshooting
  7. DJ Sterrett
    Thread

    How do I fix this? (cura 2.5)

    Using Cura 2.5. Can't get curved surfaces to print correctly. The square surfaces print fine. See picture for curved surface. Thanks in advance
    Thread by: DJ Sterrett, May 5, 2019, 1 replies, in forum: Software
  8. DJ Sterrett
    Post

    Answered Replacement heater

    Found someone on Amazon that will make me a heater for the bed. Specs: 225mm x 225mm version 12V 120W With 3M adhesive backing With NTC100K...
    Post by: DJ Sterrett, Feb 24, 2019 in forum: Troubleshooting
  9. DJ Sterrett
    Thread

    Answered Replacement heater

    Ive been looking around for a replacement heater for my heated bed. I can't seem to find anything with a low enough wattage. Any help would be...
    Thread by: DJ Sterrett, Feb 23, 2019, 2 replies, in forum: Troubleshooting
  10. DJ Sterrett
    Post

    Solved Print cooling causes temp fall err

    I did reposition the fan with the adapter i printed off. Ive been printing with the E3dv6 for about a year no problems. The problems arrived...
    Post by: DJ Sterrett, Feb 20, 2019 in forum: Troubleshooting
  11. DJ Sterrett
    Thread

    Solved Print cooling causes temp fall err

    I recently cracked my bed on my r1 plus. I mended it back together with blue painters tape. Ever since the I have been getting a temp fall err....
    Thread by: DJ Sterrett, Feb 19, 2019, 6 replies, in forum: Troubleshooting