1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Hp0106

  1. Hp0106
    Post

    Solved Overextruded layers

    Hey everybody I know this thread has been dead for a while but I have an update to the problem I thought I fixed an I wasn't sure if I should...
    Post by: Hp0106, Aug 1, 2016 in forum: Troubleshooting
  2. Hp0106
    Post

    Solved Overextruded layers

    I tried that at first but couldn't get it to budge. I wil reassemble it and try again. I'm guessing it's just as tight when the quick release goes...
    Post by: Hp0106, Jun 22, 2016 in forum: Troubleshooting
  3. Hp0106
    Post

    Solved Overextruded layers

    [ATTACH] I decided to take my hot end out to fully clear it and make sure there was no partial blockage causing inconsistent extrusion. But I...
    Post by: Hp0106, Jun 22, 2016 in forum: Troubleshooting
  4. Hp0106
    Post

    Solved Overextruded layers

    Lots of suggestions to try. Thank you everybody I would never have thought to try any of this on my own. I will try fully clearing the nozzle and...
    Post by: Hp0106, Jun 22, 2016 in forum: Troubleshooting
  5. Hp0106
    Post

    Solved Overextruded layers

    [ATTACH] I have printed the calibration cube and it does look much better. I don't think the bulge is from a new layer because of reoccurrences...
    Post by: Hp0106, Jun 22, 2016 in forum: Troubleshooting
  6. Hp0106
    Post

    Solved Overextruded layers

    [ATTACH] It seems that the problem is still there but is slightly better. I'm still open to suggestions. Thank you guys so much for your help.
    Post by: Hp0106, Jun 21, 2016 in forum: Troubleshooting
  7. Hp0106
    Post

    Solved Overextruded layers

    Alright firmware has been uploaded to the printer. I'm running a test print now. Thanks for the help guys I'll share my results later.
    Post by: Hp0106, Jun 21, 2016 in forum: Troubleshooting
  8. Hp0106
    Post

    Solved Overextruded layers

    Alright I have my new E-steps and I'm ready to put them in. In the video he talks about using gcode commands or recompiling to save the new steps....
    Post by: Hp0106, Jun 21, 2016 in forum: Troubleshooting
  9. Hp0106
    Post

    Solved Overextruded layers

    Belts are tight and no slipping on the drive gears. I'm about to calibrate the extruder. Thanks for the help so far.
    Post by: Hp0106, Jun 21, 2016 in forum: Troubleshooting
  10. Hp0106
    Post

    Solved Overextruded layers

    Thanks for the quick reply. I will calibrate the extruder and I know the belts are fine but how do I check the drive gears for slop?
    Post by: Hp0106, Jun 21, 2016 in forum: Troubleshooting
  11. Hp0106
    Thread

    Solved Overextruded layers

    [ATTACH] Hey guys, I've run into a problem where some of my layers are bulging or look like the printer overextruded. I have tried using an...
    Thread by: Hp0106, Jun 21, 2016, 25 replies, in forum: Troubleshooting
  12. Hp0106
    Post

    Answered Which 3D Printer with 3 nozzle/colors/material

    Here is something that allows a single nozzle printer print up to 4 colors or materials. http://www.mosaicmanufacturing.com
    Post by: Hp0106, May 21, 2016 in forum: General Questions
  13. Hp0106
    Post

    Solved Strange first layer

    With a small tweak to the z offset and slowing the first layer to 15mm/s everything looks nice again. Thanks for the help everyone!
    Post by: Hp0106, May 6, 2016 in forum: Troubleshooting
  14. Hp0106
    Post

    Solved Strange first layer

    Thanks for the suggestions I will try tweaking the z offset and lower the print speed as soon as I get home.
    Post by: Hp0106, May 5, 2016 in forum: Troubleshooting