1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by James Harry

  1. James Harry
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Doesn't M851 require a positive number?
    Post by: James Harry, Mar 6, 2018 in forum: Mods and Upgrades
  2. James Harry
    Post

    Thinking about Precision Piezo

    Just thought I'd add that my new z-offset with the piezo is 0.04. :)
    Post by: James Harry, Feb 28, 2018 in forum: Mods and Upgrades
  3. James Harry
    Post

    Thinking about Precision Piezo

    Two probes simultaneous gives this deviation: 0.020 0.002 0.008 0.013 0.020 0.002 0.016 0.001 0.016 0.012 0.008 0.001 0.001 0.000 0.018 0.026...
    Post by: James Harry, Feb 26, 2018 in forum: Mods and Upgrades
  4. James Harry
    Post

    Thinking about Precision Piezo

    Here's my latest bed map: Bed Topography Report for CSV: -0.300,-0.277,-0.244,-0.202,-0.182,-0.137,-0.207...
    Post by: James Harry, Feb 26, 2018 in forum: Mods and Upgrades
  5. James Harry
    Post

    Thinking about Precision Piezo

    I had it all together and struggled a bit, but the folks that sell this helped me realize the polarity was reversed, so a quick switch and it was...
    Post by: James Harry, Feb 25, 2018 in forum: Mods and Upgrades
  6. James Harry
    Post

    Thinking about Precision Piezo

    The R1's mount for hexagon hotend with part fan will definitely need a different adapter. I took off the part fan and mount when I originally...
    Post by: James Harry, Feb 21, 2018 in forum: Mods and Upgrades
  7. James Harry
    Post

    Thinking about Precision Piezo

    Funny, I was just prepping an update... The shipping time wasn't too bad. I've been working on it, although a bit slowly due to work...
    Post by: James Harry, Feb 21, 2018 in forum: Mods and Upgrades
  8. James Harry
    Post

    Recommend a used C2?

    My thoughts exactly as it have a friend with a M2. Unfortunately, it was sold before I could even get a reply.
    Post by: James Harry, Feb 20, 2018 in forum: General Questions
  9. James Harry
    Post

    Recommend a used C2?

    Iw will have to check out BluPrint. On the R1, I use PEI on the bed and it's fantastic. Can be way too sticky without the right height...
    Post by: James Harry, Feb 17, 2018 in forum: General Questions
  10. James Harry
    Post

    Recommend a used C2?

    Thanks, that's helpful. I'm not necessarily against PLA, but a lot of my prints are for car fixes, or other parts that need to be a bit more heat...
    Post by: James Harry, Feb 17, 2018 in forum: General Questions
  11. James Harry
    Post

    Recommend a used C2?

    My R1 has been upgraded quite a few times. Thinking of replacing the RAMPS with a MKS 1.5 that I have. Getting a MINTEMP error right now, so...
    Post by: James Harry, Feb 17, 2018 in forum: General Questions
  12. James Harry
    Post

    Recommend a used C2?

    Thanks, Geof, that would be helpful. I currently have an upgraded R1 and right now only print ABS on it. I looked at Robo's product page, and it...
    Post by: James Harry, Feb 17, 2018 in forum: General Questions
  13. James Harry
    Post

    Recommend a used C2?

    Cool, thanks guys. :)
    Post by: James Harry, Feb 17, 2018 in forum: General Questions
  14. James Harry
    Thread

    Recommend a used C2?

    Would you recommend a used C2 for $300-350? I've not really followed the new models, but one is available so I'm considering...
    Thread by: James Harry, Feb 16, 2018, 20 replies, in forum: General Questions