1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by John Wohlfeil

  1. John Wohlfeil
    Post

    Robo R2 Z Wizard wont calibrate correctly

    After sitting for a couple of years, I turned on my Robo R2 printer and immediately updated the firmware on the machine to RoboOS 2.0.0-r2.6 using...
    Post by: John Wohlfeil, Nov 25, 2021 in forum: Troubleshooting
  2. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    Of course I will watch and read all I can. My experience with Simplify 3D is just my initial set up and printing using Mosaic Palette+ , and...
    Post by: John Wohlfeil, Jan 3, 2018 in forum: General Questions
  3. John Wohlfeil
    Post

    What do I want for Christmas?

    I know NOTHING about 3D printing - and when I found out about adding the 2nd extruder - I COULDN'T WAIT to get it. Now that I've been wrestling...
    Post by: John Wohlfeil, Jan 1, 2018 in forum: General Questions
  4. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    I am using Ultimaker Cura 3.0.4 with the printer set up to use 4 different extruders. Meanwhile, I had been successfully printing one color since...
    Post by: John Wohlfeil, Jan 1, 2018 in forum: General Questions
  5. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    Benchy looks great! I think all of my problems were with the set up. I am using PLA from the same manufacturer (Hatchbox) and I only had those...
    Post by: John Wohlfeil, Jan 1, 2018 in forum: General Questions
  6. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    I have been back and forth and hit a number of road blocks along the way. Both Robo and Mosaic have been very helpful and very responsive. Most...
    Post by: John Wohlfeil, Dec 10, 2017 in forum: General Questions
  7. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    Success !!!!! I have successfully printed 4-Color objects on Robo R2 using Mosaic Palette+.
    Post by: John Wohlfeil, Dec 10, 2017 in forum: General Questions
  8. John Wohlfeil
    Post

    Hotend Clogged and other challenges

    The temp gauge appears to be working. The reading goes up a bit as I handle the hot end assembly. Then goes back down a bit as I let go. The...
    Post by: John Wohlfeil, Nov 27, 2017 in forum: Troubleshooting
  9. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    Its not that I NEED a low poly Link model that badly, but I have to test print SOMETHING. I have sent an email to Robo support - and I'm hoping...
    Post by: John Wohlfeil, Nov 27, 2017 in forum: General Questions
  10. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    I was hoping to give a full account of my experience with the Robo R2 and the Mosaic Palette+ , but since I's currently stuck in the mud and...
    Post by: John Wohlfeil, Nov 27, 2017 in forum: General Questions
  11. John Wohlfeil
    Post

    Anyone have experience with Palette+ ?

    Mini-Update ... things are not going well with the Robo R2 and Mosaic Palette+
    Post by: John Wohlfeil, Nov 27, 2017 in forum: General Questions
  12. John Wohlfeil
    Post

    Hotend Clogged and other challenges

    Yeah, I have it in the correct plug, the end that I can see doesn't look damaged, but its tiny. I hope the female end isn't damaged inside. That...
    Post by: John Wohlfeil, Nov 27, 2017 in forum: Troubleshooting
  13. John Wohlfeil
    Post

    Hotend Clogged and other challenges

    Ive got it put back together and the heat wires plugged in, and the hot end assembly put back in place - still clogged. Now it won't heat up,...
    Post by: John Wohlfeil, Nov 26, 2017 in forum: Troubleshooting
  14. John Wohlfeil
    Thread

    Hotend Clogged and other challenges

    I have a clogged hot end. Filament is stuck down in there. When I remove the hot end assembly by loosening the single hex screw in front, the...
    Thread by: John Wohlfeil, Nov 26, 2017, 6 replies, in forum: Troubleshooting