1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jwmueller

  1. jwmueller
    Post

    E3D Titan Extruder Top

    Thanks, been interesting. Yep, got the Duet for a larger project and the price was great. The larger project got even bigger and now sits in a...
    Post by: jwmueller, Mar 3, 2018 in forum: Mods and Upgrades
  2. jwmueller
    Thread

    Hex Hotend Play

    I ended up having to replace my hex hotend after a heater fail. With my arm in a sling I did the job with well one hand, not fun but it lead to a...
    Thread by: jwmueller, Mar 3, 2018, 2 replies, in forum: Troubleshooting
  3. jwmueller
    Post

    E3D Titan Extruder Top

    Thanks will download and let you know. ;) Here is my problem with the hex hotend, each time it hits say a blob or imperfection in the prints,...
    Post by: jwmueller, Mar 3, 2018 in forum: Mods and Upgrades
  4. jwmueller
    Post

    E3D Titan Extruder Top

    I have to put a heatsink on the stock R2 stepper, and even with that it gets hot enough to soften the filament to an eventual jam. I have been...
    Post by: jwmueller, Mar 3, 2018 in forum: Mods and Upgrades
  5. jwmueller
    Post

    E3D Titan Extruder Top

    Thanks for sharing, I recently discovered part of my Z variations are down to the hex moving. Plus I just stripped it out while trying to put in...
    Post by: jwmueller, Mar 3, 2018 in forum: Mods and Upgrades
  6. jwmueller
    Post

    First layer issues

    It is not bad to be honest. The upper gantry molded plastic is only held on be a few screws, so you take those and the wire harness off. Then it...
    Post by: jwmueller, Nov 6, 2017 in forum: Troubleshooting
  7. jwmueller
    Thread

    Updated Fan Duct from Robo

    File is too large - so here is a link to it. Thanks to Jason for emailing it over to us. Edit: It should now be up in the Robo Thingiverse...
    Thread by: jwmueller, Nov 6, 2017, 9 replies, in forum: Mods and Upgrades
  8. jwmueller
    Post

    Uneven Z-Banding

    Check for play on the extruder gantry itself, and check for Z-axis wobble from the lead screw. It does not fully look like Z-wobble as the...
    Post by: jwmueller, Nov 6, 2017 in forum: Troubleshooting
  9. jwmueller
    Post

    First layer issues

    Similar to how mine looked before I replaced the rods, after that my layer lines were great. Rods are easy to check. Center the extruder by hand...
    Post by: jwmueller, Nov 6, 2017 in forum: Troubleshooting
  10. jwmueller
    Post

    Gap between passes on solid layers using s3d

    Ok on your factory file, change: Under Extruder Tab Extrusion Multiplier to 1.00 Under the Layer Tab I would probably change the Frist Layer...
    Post by: jwmueller, Nov 5, 2017 in forum: Troubleshooting
  11. jwmueller
    Post

    Gap between passes on solid layers using s3d

    Can you share your FFF file with us so we can take a look? I would send you mine but it has a bunch of printers with many processes. LOL Edit:...
    Post by: jwmueller, Nov 4, 2017 in forum: Troubleshooting
  12. jwmueller
    Post

    R2 Click and Snapping Sounds

    I have at least 1mm in each direction and I can see the bearings inside the gantry moving (on the OD). Going to order in some from Misumi and...
    Post by: jwmueller, Nov 4, 2017 in forum: Troubleshooting
  13. jwmueller
    Post

    Not printing correct dimensions

    Check to make sure all your set screws are tight on the rods. Just a sanity check, they like to come loose and if so they can ever so slightly...
    Post by: jwmueller, Nov 3, 2017 in forum: Troubleshooting