1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by JWW

  1. JWW
    Post

    slicer support question

    ... thanks for the input. I'll rethink the design.
    Post by: JWW, Jan 15, 2022 in forum: General Questions
  2. JWW
    Post

    slicer support question

    No, I haven't considered that. It needs to be smooth on both sides.
    Post by: JWW, Jan 14, 2022 in forum: General Questions
  3. JWW
    Thread

    slicer support question

    I'm trying to design a stage fixture for a bullet comparison forensic microscope. I sure would appreciate a suggestion on what support method I...
    Thread by: JWW, Jan 14, 2022, 7 replies, in forum: General Questions
  4. JWW
    Post

    Unanswered First layer

    I designed a fixture so to speak for a Leica Bullet Stage to adapt to my Nikon MM-11 toolmakers microscope baseplate. The Bullet Stange has...
    Post by: JWW, Dec 20, 2021 in forum: Troubleshooting
  5. JWW
    Post

    Unanswered First layer

    I wasn't looking for anything special, just PLA that prints well on a Robo R1 plus.
    Post by: JWW, Dec 20, 2021 in forum: Troubleshooting
  6. JWW
    Post

    Unanswered First layer

    Thanks, I'll give it a shot on the next print. BTW, I did go to the Simpilify3D forum and did a few searching but it didn't come up with anything....
    Post by: JWW, Dec 14, 2021 in forum: Troubleshooting
  7. JWW
    Post

    Unanswered First layer

    I still haven't figured out how to get the actual real-time printing process to show up on the screen as MatterControl has. I'm not talking about...
    Post by: JWW, Dec 14, 2021 in forum: Troubleshooting
  8. JWW
    Post

    Unanswered First layer

    I finally have this puppy dialed in. Thanks for all the help. BTW, I have the stock nozzle in my R1 plus. Do you have any suggestions for...
    Post by: JWW, Dec 9, 2021 in forum: Troubleshooting
  9. JWW
    Post

    Solved At my wits end. Need help w/ firmware

    Man, I hope I never go through all this. I'll just buy another printer. Luckily someone like you are here to help.
    Post by: JWW, Dec 9, 2021 in forum: Troubleshooting
  10. JWW
    Post

    Unanswered First layer

    Sorry Mark, yes, I didn't notice that tab. <duh> Thanks ...
    Post by: JWW, Nov 20, 2021 in forum: Troubleshooting
  11. JWW
    Post

    Unanswered First layer

    Yes, I saw all the training videos. I also viewed the control panel but was looking for something like MatterContol method of moving all the XYZ...
    Post by: JWW, Nov 20, 2021 in forum: Troubleshooting
  12. JWW
    Post

    Unanswered First layer

    I think my issue is also an extruder issue. IF so, how would I troubleshoot that? I had to put 8 skirts on a test model before it extruded...
    Post by: JWW, Nov 19, 2021 in forum: Troubleshooting
  13. JWW
    Post

    Unanswered First layer

    Just wand some clarification please. Which is correct? M565 Z--.9 M565 Z- -.9 Note the white space between the -'s in the last example.
    Post by: JWW, Nov 19, 2021 in forum: Troubleshooting
  14. JWW
    Post

    Unanswered First layer

    I leveled the bed with a piece of paper. It took a while but wasn't difficult. Then fired up Simplify3D and printed the Benchy. I'm using all the...
    Post by: JWW, Nov 18, 2021 in forum: Troubleshooting