1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by KingaLing

  1. KingaLing
    Thread

    Leveling Bed

    What are you guys using to level out the bed, shims etc, I was thinking of using some sticky tack so I can put it on each bolt and then push down...
    Thread by: KingaLing, Dec 30, 2017, 1 replies, in forum: General Questions
  2. KingaLing
    Post

    Solved Z Offset Calibration Stays at Left Corner

    OK, thanks for the reply, after all night and using fresh eyes, I noticed I had the layer height to .5 instead of 0.5, lol I feel like an idiot.
    Post by: KingaLing, Dec 30, 2017 in forum: Troubleshooting
  3. KingaLing
    Thread

    Solved Z Offset Calibration Stays at Left Corner

    I have a question, I have been unable to use my C2 for a few months as I travel for work and did not have the time to print. Now that I have a...
    Thread by: KingaLing, Dec 30, 2017, 2 replies, in forum: Troubleshooting
  4. KingaLing
    Thread

    Unanswered Remote Access Printer Using Robo App

    I have a quick and maybe simple question, is there a way to access printer remotely through the robo3D app? I know it is Octoprint, and have...
    Thread by: KingaLing, Dec 23, 2016, 8 replies, in forum: Troubleshooting
  5. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    Also, when it was done printing, it seemed like Cura wanted the bed to go way back, as there was grinding noise for a few seconds after the bed...
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  6. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    I see, is there anything else I need to change though, as you can see in the picture, it is not burying the nozzle, but doesn't look good.
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  7. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    Guess I have to reach out to Robo and talk to them on why they charged me for one and didn't send me the correct model, thanks for all the help so...
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  8. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    So can you tell me which firmware I should download?
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  9. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    I do have a plastic bottom, so I am not sure, are you saying I do, or do not have an R1 Plus.
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  10. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    That does not match what I have, I have (80,80,800,723.38) Should I change and test, or do you think there are other areas that may be incorrect?
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  11. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    If it has those parts, should I try a different software, or something else?
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting
  12. KingaLing
    Post

    Answered Nozzle Digging Into Print (Noob)

    It does have both of those stepper drivers for Z rods.
    Post by: KingaLing, Apr 23, 2016 in forum: Troubleshooting