1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by max longstaff

  1. max longstaff
    Post

    Switching Greg's wade to Reprap i3 extruder (WIP)

    :) it's not 100% ideal would have used the e3d titan if the price weren't a factor at the minute, This setup should be a usable replacement for...
    Post by: max longstaff, Jan 8, 2017 in forum: Mods and Upgrades
  2. max longstaff
    Post

    Switching Greg's wade to Reprap i3 extruder (WIP)

    [IMG] Should work nicely, the spring that came with it was to short but replaced it an seems to work well, ( i will eventually 3d print...
    Post by: max longstaff, Jan 8, 2017 in forum: Mods and Upgrades
  3. max longstaff
    Thread

    Switching Greg's wade to Reprap i3 extruder (WIP)

    I found the Greg's wade had too many points of failure to print sustainably (well at least mine did) I have bought a reprap i3 extruder and plan...
    Thread by: max longstaff, Jan 7, 2017, 3 replies, in forum: Mods and Upgrades
  4. max longstaff
    Post

    Solved (Please help) Extruding Problems

    did drill the hole and its a tight match it squeezes in nicely however whilst printing the PFTE still manages to raise itself causing a jam
    Post by: max longstaff, Apr 22, 2016 in forum: Troubleshooting
  5. max longstaff
    Post

    Solved (Please help) Extruding Problems

    thanks jeffthemess helped me also i was using a smaller pfte tube this one im using now is tighter but i will probably also drill the hole for the...
    Post by: max longstaff, Apr 3, 2016 in forum: Troubleshooting
  6. max longstaff
    Post

    Solved (Please help) Extruding Problems

    Okay this might seem odd but hear me out :P ... I'm now pretty sure the issue is with the HeatSink... yes the HeatSink not the heatbreak :P...
    Post by: max longstaff, Apr 3, 2016 in forum: Troubleshooting
  7. max longstaff
    Post

    Solved (Please help) Extruding Problems

    I have just taken it apart cleaned every part then put it back together as tight as possible without going overboard then tested it and the issues...
    Post by: max longstaff, Mar 22, 2016 in forum: Troubleshooting
  8. max longstaff
    Post

    Solved (Please help) Extruding Problems

    American comment wasn't aimed at intelligence it was more that what was originally wrote seems pretty clear to me so thought someone from England...
    Post by: max longstaff, Mar 22, 2016 in forum: Troubleshooting
  9. max longstaff
    Post

    Solved (Please help) Extruding Problems

    in the original post I said I've tried 190-240 temps and I've tried pla and abs. my stock hex hotend was broken so cant answer that...
    Post by: max longstaff, Mar 22, 2016 in forum: Troubleshooting
  10. max longstaff
    Post

    Solved (Please help) Extruding Problems

    Sorry I forgot I was talking to Americans. the problem is both by hand and mechanical thought that was clear sorry, I can upload pictures in the...
    Post by: max longstaff, Mar 22, 2016 in forum: Troubleshooting
  11. max longstaff
    Post

    Solved (Please help) Extruding Problems

    ... i meant if i stop spinning then try start again 2 seconds later it wont come out
    Post by: max longstaff, Mar 22, 2016 in forum: Troubleshooting
  12. max longstaff
    Thread

    Solved (Please help) Extruding Problems

    Hi, I will start by saying that I have a Robo 3d R1 with full-length rods, I have added an E3D V6 Hotend, I have been having this issue for a...
    Thread by: max longstaff, Mar 21, 2016, 26 replies, in forum: Troubleshooting
  13. max longstaff
    Post

    Unanswered prints thin/stringy and layers separate easily (weak prints)

    :) nice I now just need a new hobbed bolt and I'm ready to test print
    Post by: max longstaff, Feb 10, 2016 in forum: Troubleshooting