1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by TheKoopaGaming

  1. TheKoopaGaming
    Thread

    Answered Autoleveling not working after RAMPS replacement

    Hey, you guys have been very helpful in the past, hoping you can help me solve this problem. I just replaced my RAMPS board, and everything seems...
    Thread by: TheKoopaGaming, Oct 3, 2018, 4 replies, in forum: Troubleshooting
  2. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    Could it be anything besides this? I have repeatedly checked both and neither seem to be the problem. Could it be a code issue? Another thing is...
    Post by: TheKoopaGaming, May 13, 2017 in forum: Troubleshooting
  3. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    This is happening on both the X and Y axis. Nothing jammed in the belt- it moves around just fine. Bed moves freely, what would be blocking this?
    Post by: TheKoopaGaming, May 13, 2017 in forum: Troubleshooting
  4. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    How do I go about fixing this?
    Post by: TheKoopaGaming, May 12, 2017 in forum: Troubleshooting
  5. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    Thanks for the answer! Not sure if this would change anything but at the start of my prints there is often a grinding noise whenever the bed...
    Post by: TheKoopaGaming, May 12, 2017 in forum: Troubleshooting
  6. TheKoopaGaming
    Thread

    Unanswered X-Axis Shifting

    Hello Robo Community I have been having a problem with x-axis shifting. Whenever I try and print a model that takes up most of the build plate on...
    Thread by: TheKoopaGaming, May 9, 2017, 10 replies, in forum: Troubleshooting
  7. TheKoopaGaming
    Post

    Solved Problems Printing with PETG

    Figured this out- had to change the start gcode in Cura to get the z offset to stay set where it is. Thanks for the help!! Sent from my iPhone...
    Post by: TheKoopaGaming, Apr 22, 2017 in forum: Troubleshooting
  8. TheKoopaGaming
    Post

    Solved Problems Printing with PETG

    I'm using an XXL controller and I set the z offset to 1.5mm before the print but when I checked after the print started the controller had it set...
    Post by: TheKoopaGaming, Apr 21, 2017 in forum: Troubleshooting
  9. TheKoopaGaming
    Thread

    Solved Problems Printing with PETG

    Hello Robo Community You have been very helpful to me in the past so I hope you can help me now. This is my first time printing with PETG and I am...
    Thread by: TheKoopaGaming, Apr 21, 2017, 3 replies, in forum: Troubleshooting
  10. TheKoopaGaming
    Thread

    Solved Layer Shifting

    Hello Forum! You have been very helpful in the past so I hope you can help now! Ever since I did a little maintenance on my printer (nothing...
    Thread by: TheKoopaGaming, Feb 24, 2017, 2 replies, in forum: Troubleshooting
  11. TheKoopaGaming
    Post

    Best Robo R1+ mods

    PEI is your best friend! It is sheet of plastic that you can put on your bed and everything sticks great to it. No glue or hairspray. There are...
    Post by: TheKoopaGaming, Dec 21, 2016 in forum: Mods and Upgrades