1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by TomerO

  1. TomerO
    Thread

    Marlin 1.1.9 for Robo3D R1+ & Fan speed hotend temp protection

    Hello everyone :) I recently finished updating my printer to 1.1.9 (decided not to go for 2.0 for now). Since my code is in github I thought it...
    Thread by: TomerO, Nov 11, 2019, 1 replies, in forum: Mods and Upgrades
  2. TomerO
    Post

    Unanswered X Carriage Making Grinding Sound?

    When steppers are involved wires can also be a problem. Try and check the wires before you go into the trouble of replacing anything. (Although...
    Post by: TomerO, Sep 18, 2016 in forum: Troubleshooting
  3. TomerO
    Post

    Solved Well, Just when I thought it was all over...

    A good way I found to test it is to find a location where it doesn't work then play with the wires by hand. If it changes then you have your...
    Post by: TomerO, Sep 10, 2016 in forum: Troubleshooting
  4. TomerO
    Post

    Solved Well, Just when I thought it was all over...

    Again, really sounds like wiring problem Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Sep 10, 2016 in forum: Troubleshooting
  5. TomerO
    Post

    Solved Well, Just when I thought it was all over...

    I just had a similar problem except the motor was "stuck" at times. The problem was a wire to the stepper broke. You might have the same issue or...
    Post by: TomerO, Sep 10, 2016 in forum: Troubleshooting
  6. TomerO
    Post

    Anyone feel like sharing some pics!!

    They are holders I designed for a polycarbonate sheet bed here is a picture that shows it [IMG] Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Aug 25, 2016 in forum: Show and Tell
  7. TomerO
    Post

    Anyone feel like sharing some pics!!

    Here is mine :)[IMG] Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Aug 25, 2016 in forum: Show and Tell
  8. TomerO
    Post

    Unanswered Printer error after hot end upgrade?

    Any chance this is happening when your part cooling fans turn on? Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jul 19, 2016 in forum: Troubleshooting
  9. TomerO
    Post

    Unresolved First layer okay, second layer.. not so much.

    What speeds are you printing at? This seems very fast. Also, way too much glue give it a clean Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jul 10, 2016 in forum: Troubleshooting
  10. TomerO
    Thread

    Gradually increasing fan speed #marlin

    Background (to why I did this, you can skip this and go to the next section if you want): Since I upgraded to E3D v6 and change the fan ducts to...
    Thread by: TomerO, Jul 5, 2016, 0 replies, in forum: Mods and Upgrades
  11. TomerO
    Post

    eliminating tiny holes?

    I had/have the same issue when there is too much friction on the filament spool. (Not 100% sure that is the cause, but it seems like it) P.S:...
    Post by: TomerO, Jul 4, 2016 in forum: General Questions
  12. TomerO
    Post

    newbie question on starting the journey with 3D printing

    Enjoy Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 29, 2016 in forum: Troubleshooting
  13. TomerO
    Post

    newbie question on starting the journey with 3D printing

    Yes it is. that's the screw I was referring to Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 29, 2016 in forum: Troubleshooting