1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Joseph Stevens
    Thread

    Solved Heat sink fan not keeping up

    I'm having heat creep problems, and I think it's because the heat sink fan isn't spinning at full speed. Is there any fix for this or should I...
    Thread by: Joseph Stevens, Nov 3, 2019, 2 replies, in forum: Troubleshooting
  2. Joseph Stevens
    Post

    R2 reports constant, incorrect extruder temperature

    I use octoprint for the R2 already, and unless I'm missing something it doesn't offer near the functionality of simplify3d.
    Post by: Joseph Stevens, Oct 28, 2019 in forum: Troubleshooting
  3. Joseph Stevens
    Post

    R2 reports constant, incorrect extruder temperature

    Post by: Joseph Stevens, Oct 27, 2019 in forum: Troubleshooting
  4. Joseph Stevens
    Post

    R2 reports constant, incorrect extruder temperature

    I'm pretty sure I'm having the same problem with my R2 motherboard. Would I be able to replace it with something that would let me to control the...
    Post by: Joseph Stevens, Oct 26, 2019 in forum: Troubleshooting
  5. Joseph Stevens
    Post

    I just want to replace the hot end.

    If you mean what I think you mean, I just unscrewed it....
    Post by: Joseph Stevens, Oct 22, 2019 in forum: Mods and Upgrades
  6. Joseph Stevens
    Post

    I just want to replace the hot end.

    I swapped out the hexagon hot end on the R2 with a round E3D one and it's worked fine. I did the same for the R1+, although it required removing...
    Post by: Joseph Stevens, Oct 22, 2019 in forum: Mods and Upgrades
  7. Joseph Stevens
    Post

    Dual extrusion mod for C2

    There are two different sizes on the R2.
    Post by: Joseph Stevens, Sep 17, 2019 in forum: Mods and Upgrades
  8. Joseph Stevens
    Post

    I just want to replace the hot end.

    Do you know exactly what kind of connectors each uses? Switching out components would be a lot easier if I could just insert them into new...
    Post by: Joseph Stevens, Sep 17, 2019 in forum: Mods and Upgrades
  9. Joseph Stevens
    Post

    I just want to replace the hot end.

    The hexagon components I have now for the r1+ and r2 are identical. Are those supposed to be different apart from the wiring?
    Post by: Joseph Stevens, Sep 17, 2019 in forum: Mods and Upgrades
  10. Joseph Stevens
    Post

    I just want to replace the hot end.

    I have the aluminum hexagon part of the extruder. I need a new heater block. I bought some this summer, but the size was sufficiently off that I...
    Post by: Joseph Stevens, Sep 16, 2019 in forum: Mods and Upgrades
  11. Joseph Stevens
    Thread

    I just want to replace the hot end.

    I can't wait for parts direct to get a new shipment, I just need a link to something I can order from Amazon, plug it into the R2 I've been...
    Thread by: Joseph Stevens, Sep 13, 2019, 30 replies, in forum: Mods and Upgrades
  12. Joseph Stevens
    Post

    Serious Bed Homing Problem

    No, I mean the autoleveling sensor. Here's the email I got from Robo a few months ago: Hi Joseph, Unfortunately we are out of the IR sensors so...
    Post by: Joseph Stevens, Jul 12, 2019 in forum: Troubleshooting
  13. Joseph Stevens
    Post

    Serious Bed Homing Problem

    Sorry if this was covered above and I missed it, but when I was having problems with the IR sensor, I was told by Robo to just disable it, since...
    Post by: Joseph Stevens, Jul 8, 2019 in forum: Troubleshooting
  14. Joseph Stevens
    Post

    persistent ringing problem

    Ok. Any suggestions about the layer shifting?
    Post by: Joseph Stevens, Jun 18, 2019 in forum: Troubleshooting
  15. Joseph Stevens
    Thread

    persistent ringing problem

    Apparently I can't upload photos for some reason. Printing from Cura 4.1 on a Mac. I've done the gantry alignment thing. Is there not a Robo R2...
    Thread by: Joseph Stevens, Jun 18, 2019, 6 replies, in forum: Troubleshooting
  16. Joseph Stevens
    Thread

    Advanced Variables

    What are the advanced variables under EEPROM? Does Z specify the nozzle size? The default value for Z is .4.
    Thread by: Joseph Stevens, Apr 30, 2019, 1 replies, in forum: General Questions
Showing results 1 to 16 of 16
Search Again