1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. zolagg
    Post

    Solved E3d pt100 problems.

    Actually no. When I'm done making changes in the Arduino program I hook my computer to my printer with a usb cable and then hit upload. After...
    Post by: zolagg, Sep 12, 2016 in forum: Troubleshooting
  2. zolagg
    Post

    Solved E3d pt100 problems.

    I should also note that when I upload the firmware back to the stud thermistor the lcd shows 0 until I hook everything up and then itshows the...
    Post by: zolagg, Sep 12, 2016 in forum: Troubleshooting
  3. zolagg
    Post

    Solved E3d pt100 problems.

    Ok so I found out I actually have both the pt100 and the cartridge thermistor. The thing is when I hook either one up nothing changes. As soon as...
    Post by: zolagg, Sep 12, 2016 in forum: Troubleshooting
  4. zolagg
    Post

    Solved E3d pt100 problems.

    Wow that's some helpful information. Thanks. I will try this evening and repost.
    Post by: zolagg, Sep 12, 2016 in forum: Troubleshooting
  5. zolagg
    Post

    Solved E3d pt100 problems.

    Yes. Sorry I forgot to mention that part. I do hook up the amplifier but that doesn't change anything with the temp display.
    Post by: zolagg, Sep 12, 2016 in forum: Troubleshooting
  6. zolagg
    Thread

    Solved E3d pt100 problems.

    I'm havingtrouble using the pt100 temp sensor from e3d on my robo 3d r1 plus. I have followed installation directions exactly changing firmware...
    Thread by: zolagg, Sep 11, 2016, 11 replies, in forum: Troubleshooting
  7. zolagg
    Thread

    Unresolved Bed leveling problem

    Ok I have a new problem with the bed leveling on my robo 3d r1 plus. I noticed lately that some of my larger prints or when I place multiple...
    Thread by: zolagg, Sep 6, 2016, 2 replies, in forum: Troubleshooting
  8. zolagg
    Post

    Solved Z axis problems.

    The printer is working great again! Thank you for all of your help.
    Post by: zolagg, Aug 8, 2016 in forum: Troubleshooting
  9. zolagg
    Post

    Solved Z axis problems.

    Ok I will check the switches. The z offset does make sense because I have 2 different printer profile settings and one prints in the air and the...
    Post by: zolagg, Aug 4, 2016 in forum: Troubleshooting
  10. zolagg
    Thread

    Solved Z axis problems.

    Hello all. This is my first time posting on this forum and I'm hoping someone could help. I recently changed my stock hot end on my robo 3d r1...
    Thread by: zolagg, Aug 3, 2016, 4 replies, in forum: Troubleshooting
  11. zolagg
    Post

    Solved MAX TEMP Error on E3D v6 Hotend

    I am having the same issue. I installed the e3dv6 along with the pt100 stud. My screen says maxtemp error and shows the hot end temp at 430? I...
    Post by: zolagg, Jul 31, 2016 in forum: Troubleshooting
  12. zolagg
    Post

    E3D v6 Information, Installation Guides, and Review

    Ok great info. Thanks for the help. Reprinting one with the printer all taken apart was not a good option for me. I will definitely use the tape!
    Post by: zolagg, Jul 30, 2016 in forum: Mods and Upgrades
  13. zolagg
    Post

    E3D v6 Information, Installation Guides, and Review

    Thanks for the great write up. The problem I'm having is that my hot end does not fit tight when everything is assembled. I have the robo plus...
    Post by: zolagg, Jul 30, 2016 in forum: Mods and Upgrades
Showing results 1 to 13 of 13
Search Again