1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. wuidling
    Thread

    GCode (Newbie)

    Hello, a little Questions of understanding. If i send a file to the Robo (Upload) created by Cura how does the sequence start ? Octoprint -...
    Thread by: wuidling, Apr 6, 2020, 5 replies, in forum: Troubleshooting
  2. wuidling
    Thread

    ROBO R2 Installation

    Servus, nachdem ich mir einen neuen R2 über Ebay gekauft habe möchte meine Erfahrung mit diesem Drucker teilen und Hilfestellung zur Einrichtung...
    Thread by: wuidling, Apr 5, 2020, 6 replies, in forum: Germany
  3. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Finally i changed the SD Card to 64GB with the suggested Image. R2 prints with the 1.2.6 HEX-Version and Offset & Fine Offset are now working...
    Post by: wuidling, Apr 5, 2020 in forum: Troubleshooting
  4. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    This explains the price i payed for a unused R2 at ebay. But for a beginner i think the printer is optimal for testing and learning. Regards
    Post by: wuidling, Apr 3, 2020 in forum: Troubleshooting
  5. wuidling
    Post

    First Layers (Newbie)

    First of all, thanks for the support. I tried several options on cura (Raft/Brim/Line Width/First Layer...) but the first layer is not like i...
    Post by: wuidling, Apr 3, 2020 in forum: Troubleshooting
  6. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Hello, Can someone tell me why the wrong z-settings are not fixed in the firmware ? It is frustrating when you do the complete setup...
    Post by: wuidling, Apr 3, 2020 in forum: Troubleshooting
  7. wuidling
    Post

    First Layers (Newbie)

    Hello and thanks for youre support. So i leveled the bed exactly and checked the fine offset. i printed another simple piece with the default...
    Post by: wuidling, Apr 2, 2020 in forum: Troubleshooting
  8. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    I tested the latest Robo 1.2.4 and 1-2.6. both with positive z-offset and problems with fine offset adjustment (motor stops sometimes x/y) so i...
    Post by: wuidling, Apr 2, 2020 in forum: Troubleshooting
  9. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    You're right. Newbie mistake !
    Post by: wuidling, Apr 1, 2020 in forum: Troubleshooting
  10. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Thanks for the support, Is this the right way to get the original firmware: First off, do a reset of the firmware parameters. Using the terminal...
    Post by: wuidling, Apr 1, 2020 in forum: Troubleshooting
  11. wuidling
    Post

    First Layers (Newbie)

    Bottom Regards
    Post by: wuidling, Mar 31, 2020 in forum: Troubleshooting
  12. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    That's right, but we are in the R2 Forum so i think the tolerance should be in a few millimeters.
    Post by: wuidling, Mar 31, 2020 in forum: Troubleshooting
  13. wuidling
    Post

    First Layers (Newbie)

    Here is a Picture:
    Post by: wuidling, Mar 31, 2020 in forum: Troubleshooting
  14. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    The Offset should be between -7,3-7,5 mm.
    Post by: wuidling, Mar 31, 2020 in forum: Troubleshooting
  15. wuidling
    Thread

    First Layers (Newbie)

    Hello, after hours of research (Z-Offset +/-) finally the ROBO 3D R2 and the Calibration works.. After three Testpints i think the first layers...
    Thread by: wuidling, Mar 31, 2020, 11 replies, in forum: Troubleshooting
  16. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    1. RoboOS 2.0.0-r2.6 2. Official Firmware: Marlin.R2.1.1.7.hex Only this combination works on the R2 ! Otherwise the Z-Offset failed and you have...
    Post by: wuidling, Mar 31, 2020 in forum: Troubleshooting
Find older messages
Showing results 41 to 56 of 56
Search Again
Page 3 of 3