1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Greg Sheets
    Profile Post

    you asked about someone living hear Durham NC, I do

    you asked about someone living hear Durham NC, I do
    Profile post by Greg Sheets for Jerry RoBo 3D, Jan 22, 2018
  2. Greg Sheets
    Thread

    Anti vibration algorithm to speed up printing- article says going to be in Marlin

    http://www.3ders.org/articles/20171020-university-of-michigan-professor-doubles-3d-printing-speeds-using-vibration-mitigating-algorithm.html...
    Thread by: Greg Sheets, Oct 21, 2017, 2 replies, in forum: Mods and Upgrades
  3. Greg Sheets
    Post

    Verticle rod and toranado

    I understand the reduced weight, but has anybody pushed the "printing" speeds and/or changed the acceleration settings? What I really like about...
    Post by: Greg Sheets, Mar 6, 2017 in forum: Mods and Upgrades
  4. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @WheresWaldo : I can help -- I think I've been using G28 stand-alone, so no issue there. At the end script I do already use G1 X0 Y220, so no...
    Post by: Greg Sheets, May 18, 2016 in forum: Mods and Upgrades
  5. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @WheresWaldo OK, good experiment on M501. I started using M501 during RC5 days when I always got "mesh not active" notice. Good to know it works...
    Post by: Greg Sheets, May 5, 2016 in forum: Mods and Upgrades
  6. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @zenekNY One more thing I learned. If the printer goes into "disable motors" mode at the end of the print, then you will get the "mesh not...
    Post by: Greg Sheets, May 4, 2016 in forum: Mods and Upgrades
  7. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @zenekNY : See my post #338 (page 17) for my start script. I originally used the terminal to issue the G29 S1 (mesh level), but now just use the...
    Post by: Greg Sheets, May 4, 2016 in forum: Mods and Upgrades
  8. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @zenekNY : I don't use te M420 commands, but I did find it in the code source. My procedure 1) Manual MBL from LCD control, 3x3 matrix 2) Store...
    Post by: Greg Sheets, May 4, 2016 in forum: Mods and Upgrades
  9. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @zenekNY , My understanding of the wiki notes and other comments, it is either Mesh (MBL) or Auto (ABL), but not both. In my config I comment...
    Post by: Greg Sheets, May 4, 2016 in forum: Mods and Upgrades
  10. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Once the mesh is stored, and the printer is power cycled (i.e. off then back on), it will forget that it has mesh data. You need to issue a load...
    Post by: Greg Sheets, May 4, 2016 in forum: Mods and Upgrades
  11. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yes, we need <CNTL-ALT-DEL> function ;)
    Post by: Greg Sheets, May 2, 2016 in forum: Mods and Upgrades
  12. Greg Sheets
    Post

    Simplify 3d

    Instead of a 40mm line, I use 2 to 5 "skirts" (see "Additions/Use Skirt/Brim"), to get the extruder operating and verify all good on z height. I...
    Post by: Greg Sheets, May 1, 2016 in forum: Software
  13. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    OK, I too had issues with Z after first few prints. Went back to M502 to clear EEPROM, manual bed level, then M500 to store. Using my start...
    Post by: Greg Sheets, May 1, 2016 in forum: Mods and Upgrades
  14. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I just uploaded RC6. Mesh level works better than RC5, i.e. no longer dragging hot end over glass during manual mesh level). Otherwise, no noted...
    Post by: Greg Sheets, May 1, 2016 in forum: Mods and Upgrades
  15. Greg Sheets
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    OK, after a long hiatius, I got my Robo3D back up and running. I also got RC5 running with mesh leveling and all I can say is "Wow!". I've got a...
    Post by: Greg Sheets, Apr 16, 2016 in forum: Mods and Upgrades
Showing results 1 to 15 of 15
Search Again