1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. trevely
    Post

    Bearings Problem

    I did take pictures and I will gladly do a write up on this in case anyone else feels the need to go through my pain lol... l think it's printing...
    Post by: trevely, Nov 26, 2018 in forum: Troubleshooting
  2. trevely
    Post

    Bearings Problem

    Well I would like to thank everyone for there help and Jason from Robo as I was able to finally get this resolved. As I stated one of the...
    Post by: trevely, Nov 26, 2018 in forum: Troubleshooting
  3. trevely
    Post

    Bearings Problem

    At the rate I'm going with this lately I'll be able to take it apart and put it back together with my eyes closed. Well that's if I can ever get...
    Post by: trevely, Nov 19, 2018 in forum: Troubleshooting
  4. trevely
    Post

    Bearings Problem

    I checked the gantry and the rod to make sure nothing is bent and it all seems fine. If I push on the rod where it's not centered on the bearings...
    Post by: trevely, Nov 18, 2018 in forum: Troubleshooting
  5. trevely
    Post

    Bearings Problem

    I'm noticing that as I'm trying to get it replaced, like it's press-fit into the case and I think it is. It almost seems like the rod is to long...
    Post by: trevely, Nov 17, 2018 in forum: Troubleshooting
  6. trevely
    Post

    Bearings Problem

    Standing by
    Post by: trevely, Nov 17, 2018 in forum: Troubleshooting
  7. trevely
    Thread

    Bearings Problem

    Hi all, Once again I'm having issues with my Robo R2. Awhile back I was having a problem with prints shifting and it turned out to be one of the...
    Thread by: trevely, Nov 17, 2018, 20 replies, in forum: Troubleshooting
  8. trevely
    Post

    Major Printing Problems

    I would like to thank all of you for your help and suggestions. I had to take it apart as one of the belts was loose and the bearing where...
    Post by: trevely, Oct 28, 2018 in forum: Troubleshooting
  9. trevely
    Post

    Major Printing Problems

    I've had it for about 6 months or so and I reported it grinding before prints to Robo support but no real resolution came from it. I can promise...
    Post by: trevely, Oct 24, 2018 in forum: Troubleshooting
  10. trevely
    Post

    Major Printing Problems

    Thanks I will give that a look see as yeah all my prints have been toast.
    Post by: trevely, Oct 24, 2018 in forum: Troubleshooting
  11. trevely
    Post

    Major Printing Problems

    Yes this is on the R2. The first layer is not coming loose, it's sticking to the bed no problem. I was afraid it would be something like that and...
    Post by: trevely, Oct 24, 2018 in forum: Troubleshooting
  12. trevely
    Thread

    Major Printing Problems

    Hi all, Any help/guidance, anything will be appreciated if you can help me figure out what is going on with my printer or my prints. I recently...
    Thread by: trevely, Oct 23, 2018, 10 replies, in forum: Troubleshooting
  13. trevely
    Post

    Starting to get frustrated

    I would like to thank everyone for there help as I'm back to printing. The brass brush is a great idea, heated up the nozzle and the plastic...
    Post by: trevely, Aug 18, 2018 in forum: Troubleshooting
  14. trevely
    Post

    Starting to get frustrated

    I went to 240c but I'll take it higher and see if it helps. Thanks.
    Post by: trevely, Aug 10, 2018 in forum: Troubleshooting
  15. trevely
    Post

    Starting to get frustrated

    Tried that, didn't work at all.... When I get a clog I make sure it's really clogged up :D
    Post by: trevely, Aug 10, 2018 in forum: Troubleshooting
  16. trevely
    Post

    Starting to get frustrated

    Thank you all for the suggestions as I've had about 4 successful prints by adding some hairspray to the bed, lowering the z offset and letting it...
    Post by: trevely, Aug 10, 2018 in forum: Troubleshooting
  17. trevely
    Post

    Starting to get frustrated

    I didn't mention that before but I have tried to let it cool down then remove it but not much luck. I've also let it cool down then heat it back...
    Post by: trevely, Aug 6, 2018 in forum: Troubleshooting
  18. trevely
    Post

    Starting to get frustrated

    Thanks for those suggestions as well Geof, I will give them a try. I do have one more sheet as I ordered 2 in my last order just because of this...
    Post by: trevely, Aug 6, 2018 in forum: Troubleshooting
  19. trevely
    Post

    Starting to get frustrated

    Hi Mark, I'll give that a try and see what happens. Thanks for the help.
    Post by: trevely, Aug 5, 2018 in forum: Troubleshooting
  20. trevely
    Thread

    Starting to get frustrated

    Hi all, I'm not sure what is going on but lately I've been having problems with my prints ruining the sheet on the bed when trying to get the...
    Thread by: trevely, Aug 5, 2018, 21 replies, in forum: Troubleshooting
Showing results 1 to 20 of 28 Next >
Search Again
Page 1 of 2