1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 7
  1. Doug Gebhart
    Post

    Unresolved Rear Right Corner of Bed Has Prints Not Adhering

    So I just looked, and the heating element is under that area, or at least I feel a bulge under that area. EDIT: word
    Post by: Doug Gebhart, Mar 23, 2017 in forum: Troubleshooting
  2. colton81
    Post

    Back to issues again...

    Well still working on getting it leveled something is way off though the z wizard said it was -4.6 which was way off to what i had before -5.1 but...
    Post by: colton81, Mar 4, 2017 in forum: Troubleshooting
  3. Gary Boyce
    Post

    Very Frustrated. First layer, every layer, problems

    Sorry Geof, I think my frustration was showing. I didn't mean to seem abrasive to your suggestions. I haven't changed anything in EEprom yet, but...
    Post by: Gary Boyce, Jun 23, 2018 in forum: Troubleshooting
  4. mark tomlinson
    Post

    Kickstarter Edition: Full rebuild help

    Check the drive with the bed off to make sure when you move the rails full stop on the Y axis (end-to-end) that the belt is not travelling up/down...
    Post by: mark tomlinson, Apr 7, 2017 in forum: Mods and Upgrades
  5. Matt Shields
    Post

    Unresolved Troubleshooting help

    Hello everyone, I am new to 3D printers. I recently purchased a Robo R1+. I set it up per the instructional video and tried to print the...
    Post by: Matt Shields, Mar 27, 2016 in forum: Troubleshooting
  6. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    Great you have it dialed in, it is quite maddening until you locate the source of the problem,,,,Good going.......One of these daze, I will print...
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  7. Marcus T
    Post

    E3D Titan Extruder

    The effective print area on the Robo's bed is already off centered to the rear. I had thought about this problem previously. To center the hotend...
    Post by: Marcus T, Apr 17, 2016 in forum: Mods and Upgrades
  8. Jason Hopkins
    Post

    Unanswered Question on Y axis, time to learn some new stuff

    Hello, All I have been working on some stuff, unfortunately don't want to mention yet. With doing this I thing I screwed up my y axis and I'm...
    Post by: Jason Hopkins, Oct 12, 2021 in forum: Troubleshooting
  9. fred3d
    Post

    Solved Z axis only moves up won't move down past a curtain point

    I have a Robo 3D R1+ and have had that problem in the past. I'm not certain this is the perfect answer, but it worked for me. With the power off,...
    Post by: fred3d, Jul 21, 2020 in forum: Troubleshooting
  10. Drmike
    Post

    Unanswered Z axis offset way off

    I think it's too simple! You don't even need the system powered on from the description by WheresWaldo. I did something similar with a level and...
    Post by: Drmike, Feb 14, 2016 in forum: Troubleshooting
  11. Schlomo
    Post

    R1+ Auto-Level not really accurate

    So. I got mine dialed in. Turns out, the front 2 magnets were placed from the factory too far apart. So, even if i shimmed something up, by...
    Post by: Schlomo, Feb 3, 2016 in forum: General Questions
  12. Nic Phillips
    Post

    Unanswered Adjusting Z Endstop for Leveling?

    So, I'm too anxious/impatient, and decided to get started on the process of leveling the bed prior to receiving any responses to my initial...
    Post by: Nic Phillips, Apr 6, 2016 in forum: Troubleshooting
  13. gearprinter
    Post

    Solved Gantry Brace (?) Broke Off + Other Issues

    Thanks Mark appreciate your help! I spent some time working on the printer and it seems to be FIXED! :D It's printing really nicely across the...
    Post by: gearprinter, Apr 8, 2021 in forum: Troubleshooting
  14. cjryker06
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Partially fixed After some adjustments to firmware and the very slow Octoprint controlled MESH leveling, first print test seems pretty good. My...
    Post by: cjryker06, Aug 8, 2016 in forum: Mods and Upgrades
  15. AbbyV
    Post

    Solved Robo 1+ is “stuck up in the ceiling” and won’t come back down

    Geof, I manually screwed the bars down and then turned on the printer and when we tried to print it drove itself down... alllllll the way down......
    Post by: AbbyV, Jan 26, 2019 in forum: Troubleshooting
  16. Toro1966
    Post

    Heater Upgrade Question

    Hey guys - looking to upgrade the bed heater in the Robo. I actually really enjoy printing with ABS and PETG and the stock heater is frankly...
    Post by: Toro1966, Jul 27, 2016 in forum: Mods and Upgrades
  17. mark tomlinson
    Post

    Question about R1 design: why is the Y-axis belt off-center?

    Just to be clear X = left-to right as you look at the printer from the front and Y is the along the bed The rails center the movement for the Y...
    Post by: mark tomlinson, Nov 16, 2020 in forum: General Questions
  18. Mike Kelly
    Post

    Community Favorite Mike Kelly's RoBo3D Enclosure

    [IMG] RoBo3D Enclosure By Mike Kelly This mod allows you to enclose your printer so as to avoid injury from the hot and moving parts, while still...
    Post by: Mike Kelly, Jun 21, 2014 in forum: Mods and Upgrades
  19. Lael
    Post

    Unresolved Robo R1+ prints not centering on y axis as shown in Mattercontrol

    Thanks for the response. And I do actually believe there must be something to troubleshoot. I am aware of the print bed (and the heat area) being...
    Post by: Lael, Feb 16, 2016 in forum: Troubleshooting
  20. PropLord
    Post

    Answered Strange rescaling during print?

    Well... I'm worried that if I get too excited I'll jynx it. (not 100% serious about that, of course) But so far, the re-scaling is FIXED! Thank...
    Post by: PropLord, Mar 14, 2017 in forum: Troubleshooting
Showing results 41 to 60 of 129 Next >
Search Again
Page 3 of 7