1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Luis Alberto
    Thread

    Unresolved Settings on Cura for printing TPE

    Greetings guys, I've been printing some pieces on this flexible filament without serious problems, I think; no jamming or clogs, printed that part...
    Thread by: Luis Alberto, Nov 10, 2016, 0 replies, in forum: Troubleshooting
  2. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Thank you, i just found a Ramps here in Mexico for about $10 usd.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  3. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Sorry, it says right in the bed. Its a R1 plus
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  4. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Im not sure. How can I Know? Sorry.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  5. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Is it necessary to change the whole board? Isnt possible to get and change only that MOSFET? And why does this happened in first place?
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  6. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    I re-weld that specific pin and shows 12v.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  7. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Found the next: The first socket was exposed to a lot of heat, and guess it should show 12v but it doesnt. The second socket looks alright and...
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  8. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Ill check that first.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  9. Luis Alberto
    Post

    Unresolved My printbed stops heating.

    Thanks. Where should I check the voltages and what values must have? i know that i have to remove the bottom cover of the printer and check there.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  10. Luis Alberto
    Thread

    Unresolved My printbed stops heating.

    Greetings, Im back again. Just like the title says, my printbed wont heat. The sensor placed there seems to be ok cause it reads the temperature,...
    Thread by: Luis Alberto, Oct 7, 2016, 33 replies, in forum: Troubleshooting
  11. Luis Alberto
    Post

    Solved Please help me. My printer keeps doing this.

    Thank you so much.
    Post by: Luis Alberto, Oct 7, 2016 in forum: Troubleshooting
  12. Luis Alberto
    Post

    Solved Please help me. My printer keeps doing this.

    Thank you Geof, Ill try to get one around here. Meanwhile igonna use this one.
    Post by: Luis Alberto, Oct 5, 2016 in forum: Troubleshooting
  13. Luis Alberto
    Post

    Solved Please help me. My printer keeps doing this.

    Well I tried seasonig with the canola oil and there were no possitive results. I found another solution, I put an extra fan beside de extruders...
    Post by: Luis Alberto, Oct 5, 2016 in forum: Troubleshooting
  14. Luis Alberto
    Post

    Solved Please help me. My printer keeps doing this.

    Im in the office so I guees I should get one.
    Post by: Luis Alberto, Sep 30, 2016 in forum: Troubleshooting
  15. Luis Alberto
    Post

    Solved Please help me. My printer keeps doing this.

    Yes, its running.
    Post by: Luis Alberto, Sep 30, 2016 in forum: Troubleshooting
  16. Luis Alberto
    Thread

    Solved Please help me. My printer keeps doing this.

    This is what happens, just prints the skirt and the first layer and when have to go to the next one stops extruding. At first happened printing...
    Thread by: Luis Alberto, Sep 29, 2016, 10 replies, in forum: Troubleshooting
  17. Luis Alberto
    Post

    Unresolved Cant print from Matter Control

    But several prints were maid via usb with good results so its kinda weird. So, What do you recommend?
    Post by: Luis Alberto, Sep 27, 2016 in forum: Troubleshooting
  18. Luis Alberto
    Post

    Unresolved Cant print from Matter Control

    Thanks man. Im gonna try with that.
    Post by: Luis Alberto, Sep 27, 2016 in forum: Troubleshooting
  19. Luis Alberto
    Thread

    Unresolved Cant print from Matter Control

    Greetings.Ive had some troubles printing from Matter Control environment, after printing the first layers filament stops flowing, the extruder...
    Thread by: Luis Alberto, Sep 27, 2016, 6 replies, in forum: Troubleshooting
  20. Luis Alberto
    Thread

    Unresolved Clogged extruder

    Get the rest of it out. I am curious if the hole is threaded. If so, you could always use one of these to replace it....
    Thread by: Luis Alberto, Sep 13, 2016, 7 replies, in forum: Troubleshooting
Showing results 1 to 20 of 41 Next >
Search Again
Page 1 of 3