1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Show us!

Discussion in 'Show and Tell' started by WheresWaldo, Jan 4, 2018.

  1. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,102
    Likes Received:
    3,103
    Either your best R2 prints or your biggest print disasters.
     
    Geof likes this.
  2. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,102
    Likes Received:
    3,103
    I'll start with this print. There are a couple of things. Printed in PLA just a bit fast (70mm/s), but still looks pretty good. Using cheap PLA from Amazon $8 / kg before XMAS, used 0.60 mm nozzle and 0.15 mm layers. Made a mistake on my support settings so the middle is solid and the support cannot be removed. I am going to reprint this after installing TL-Smoother boards.

    It is this model: https://www.thingiverse.com/thing:367130

    [​IMG]

    Sent from my SAMSUNG-SM-N910A using Tapatalk
     
    #2 WheresWaldo, Jan 4, 2018
    Last edited: Jan 4, 2018
    Geof likes this.
  3. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    5,896
    Likes Received:
    1,994
    20171106_153103.jpg
    20171106_153108.jpg
    my favorite has been this dizingof piece. No supports so overhangs got ugly in a few spots. .25 layer (i think maybe 3 ?) Hatchbox black pla from @Printed Solid 60mm/s
     
    #3 Geof, Jan 4, 2018
    Last edited: Jan 4, 2018
  4. Stephen Jolly

    Stephen Jolly New Member

    Joined:
    Jan 25, 2018
    Messages:
    3
    Likes Received:
    5
    75188458-2C81-4FD0-9B66-F2281E9EE0E8.jpeg This is a test print I did when I got my R2
     
    Geof and WheresWaldo like this.
  5. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,102
    Likes Received:
    3,103
    Printed today, PETG sprayed with matte clear coat. Since this was single perimeter, the model cooled at different rates on the faces. Resulted in interesting warps on the faces.

    Model: https://www.thingiverse.com/thing:2793733
    [​IMG]

    Sent from my SAMSUNG-SM-N910A using Tapatalk
     
    Geof likes this.
  6. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,102
    Likes Received:
    3,103
    Find this model on Thingiverse, XBOX controller stand. Printed in the cheapest natural PLA I could find on Amazon. So far the R2 has handled every cheap filament I have thrown at it, except one spool of eSun translucent blue PETG. Model located here, https://www.thingiverse.com/thing:1978236

    [​IMG]

    Sent from my SM-G965U using Tapatalk
     
    #6 WheresWaldo, May 15, 2018 at 10:07 AM
    Last edited: May 15, 2018 at 10:42 AM

Share This Page