1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

system stopped! Heater_ID: bed

Discussion in 'Troubleshooting' started by Jaak Ahelik, Oct 16, 2017.

  1. Jaak Ahelik

    Jaak Ahelik New Member

    Joined:
    Aug 22, 2017
    Messages:
    20
    Likes Received:
    8
    Unhandled communication error
    The was an unhandled error while talking to the printer. Due to that OctoPrint disconnected. Error: Heating failed, system stopped! Heater_ID: bed
     
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,597
    Likes Received:
    7,311
    You sure this is an R1 printer?
     
  3. Jaak Ahelik

    Jaak Ahelik New Member

    Joined:
    Aug 22, 2017
    Messages:
    20
    Likes Received:
    8
    Robo R2
     
  4. Jaak Ahelik

    Jaak Ahelik New Member

    Joined:
    Aug 22, 2017
    Messages:
    20
    Likes Received:
    8
    One of the pins on the left seems to be lower then others
     

    Attached Files:

  5. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,597
    Likes Received:
    7,311
    Moving this to the correct forum.
     
    Jaak Ahelik likes this.
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,597
    Likes Received:
    7,311
    Yes, the spring inside is broken. You need to get a replacement bed connector from Robo (you need to call them).

    There are a number of other threads in here (R2 forum) that discuss this.
     
    Jaak Ahelik and Geof like this.
  7. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,729
    Likes Received:
    2,330
    Indeed. Just went through the same. Pogo Pin issue. Call them and request a replacement.
     
    Jaak Ahelik likes this.
  8. Jaak Ahelik

    Jaak Ahelik New Member

    Joined:
    Aug 22, 2017
    Messages:
    20
    Likes Received:
    8
    Not just one pin, but two pins. does it happen often?
     

    Attached Files:

  9. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Not often, but enough to be a nuisance.
     
  10. Jaak Ahelik

    Jaak Ahelik New Member

    Joined:
    Aug 22, 2017
    Messages:
    20
    Likes Received:
    8
    Can I bypass the heated bed? I need to print some stuff?
     
  11. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,729
    Likes Received:
    2,330
    you can, I'd ask Robo how they would recommend you do so without voiding your warranty. those pogo pins have to make connection to the bed.

    The pogo pins are being replaced (due to failure) by a new revision bed but I do not have any details other than that. You'd have to talk with Robo regarding that.
     
    Jaak Ahelik likes this.

Share This Page