1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

reprapdiscount LCD display....cant upload the firmware

Discussion in 'Troubleshooting' started by link4044, Jul 5, 2014.

Thread Status:
Not open for further replies.
Page 1 of 4
  1. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    so i have the rep LCD and im trying to upload the firmware and i get a error message
    Arduino: 1.5.6-r2 (Windows 7), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"

    Marlin.ino:33:27: error: Configuration.h: No such file or directory
    Marlin.ino:34:18: error: pins.h: No such file or directory
    Marlin.ino:33:27: error: Configuration.h: No such file or directory
    Marlin.ino:34:18: error: pins.h: No such file or directory

    This report would have more information with
    "Show verbose output during compilation"
    enabled in File > Preferences.

    so any idea what this means and know how to solve it?
     
    #1 link4044, Jul 5, 2014
  2. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    also it doesnt seemed to read any file when i put in the SD card too
     
    #2 link4044, Jul 5, 2014
  3. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    got the firmware uploaded. some how it went. i just close the program out and reopened it and it went.

    now it still doesnt read the .stl files on the SD card
     
    #3 link4044, Jul 5, 2014
  4. AxisLab

    AxisLab Well-Known Member

    Joined:
    Dec 28, 2013
    Messages:
    322
    Likes Received:
    269
    You don't put the stl files on the card itself. You still need to slice the file in whatever software you use normally and then save the "gcode" to the sd card.
     
    #4 AxisLab, Jul 5, 2014
  5. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    cool. thank you very much. I wish it had some kind of instructions to this thing.
     
    #5 link4044, Jul 5, 2014
  6. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    Raprap.org and matterhackers.com
     
    #6 Mike Kelly, Jul 5, 2014
  7. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    now when i home it the x&y goes home but the z goes up
     
    #7 link4044, Jul 5, 2014
  8. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    R1 or PLA and/or ABS?
     
    #8 Mike Kelly, Jul 5, 2014
  9. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    PLAand ABS
     
    #9 link4044, Jul 5, 2014
  10. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    before that when i homed it, it kept on going down and the wires got twisted
     
    #10 link4044, Jul 5, 2014
  11. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    What firmware did you install
     
    #11 Mike Kelly, Jul 5, 2014
  12. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    marlin_LCD date on it was 10/4/2013
     
    #12 link4044, Jul 5, 2014
  13. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    Try the 3/14
     
    #13 Mike Kelly, Jul 5, 2014
  14. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    well didnt work. this is what i got
     

    Attached Files:

    #14 link4044, Jul 5, 2014
  15. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    i do have the auto-leveling. im trying to figure out what i need to do for that update
     
    #15 link4044, Jul 5, 2014
  16. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    #16 Mike Kelly, Jul 5, 2014
  17. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    i didnt lie to you you asked if i had a R1 or PLA and/or ABS?
     
    #17 link4044, Jul 6, 2014
  18. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    it looks liked it worked. i'll do a test print when i get home from work
     
    #18 link4044, Jul 6, 2014
  19. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,277
    Yeah you have the R1 model. Didn't mean to be hard just that it's important to be overly clear
     
    #19 Mike Kelly, Jul 6, 2014
  20. link4044

    link4044 Member

    Joined:
    May 15, 2014
    Messages:
    142
    Likes Received:
    12
    so the updated (auto-leveling) are the R1's? i have my settings to PLA ABS on the printer connection
     
    #20 link4044, Jul 7, 2014
Page 1 of 4
Thread Status:
Not open for further replies.

Share This Page