1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Erica Lindström

  1. Erica Lindström
    Post

    Trouble with z-offset

    Yes, I know. Even thoug I also do the fine tuning, the z-offset, during actual printing, becomes much higher than when finished with the fine...
    Post by: Erica Lindström, Nov 17, 2017 in forum: Troubleshooting
  2. Erica Lindström
    Thread

    Trouble with z-offset

    Recently when I do the z-offset it does not represent the correct distance between the hot end and the print bed. To get a appropriate z distance...
    Thread by: Erica Lindström, Nov 17, 2017, 3 replies, in forum: Troubleshooting
  3. Erica Lindström
    Post

    please HELP! print quality gone to hell.

    I have been doing exactly that for 3 days. The slip of paper is almost stuck under the extruder, I doubt I can position the print bed any closer...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  4. Erica Lindström
    Thread

    please HELP! print quality gone to hell.

    In the picture you can see a large green blob, it looks like a cat turd. 3 weeks ago I printed the gray item, its awesome! I tried to do that item...
    Thread by: Erica Lindström, Nov 9, 2017, 3 replies, in forum: Troubleshooting
  5. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Its just a tick in a box, can’t change the number of peripetiers. It is actually 2 counted when testning again. Still no luck. It looks so weird,...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  6. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Where do I change the perimeter? In Cura or in octo print? Cant find anything called terminal in octo print or Cura either. Im a total nincompoop...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  7. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    I do that between every print with 95% alcohol.
    Post by: Erica Lindström, Nov 8, 2017 in forum: Troubleshooting
  8. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Sorry, just noticed that this post was in the wrong section, how do I move it to R2? Here's a picture any way...
    Post by: Erica Lindström, Nov 8, 2017 in forum: Troubleshooting
  9. Erica Lindström
    Thread

    Whole first layer of print not sticking to print bed

    I will go nuts soon, so I really hope the community can help me. The first layer of my current print is a square. The whole surface of the square...
    Thread by: Erica Lindström, Nov 8, 2017, 10 replies, in forum: Troubleshooting
  10. Erica Lindström
    Thread

    OctoPi upgrade?

    I use Cura for arranging my prints evenly on the surface of the bed. then I send it to the printer and press the button "go to Octo Print". A web...
    Thread by: Erica Lindström, Nov 8, 2017, 1 replies, in forum: General Questions
  11. Erica Lindström
    Post

    settings for RoboR2 in Cura?

    Thank you! I knew this was the place to get some answers.
    Post by: Erica Lindström, Aug 14, 2017 in forum: General Questions