1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Ocsff

  1. Ocsff
    Post

    NinjaFlex filament

    Drill out and add ptfe tube because the pen tube is plastic ptfe is teflon make all the difference
    Post by: Ocsff, Jan 16, 2017 in forum: Printing Filament
  2. Ocsff
    Post

    Unresolved Z offset with M565 not working

    This happens when you don't shut simplfy3d properly. When ever I turn off the computer with out shutting simplfy3d down it corrupts the program...
    Post by: Ocsff, Oct 16, 2016 in forum: Troubleshooting
  3. Ocsff
    Post

    Unanswered Printer stoping after randomly mid print

    Ramps board over heating. Once again Mark is right on .
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  4. Ocsff
    Post

    Unresolved Tilting on x axis - how to fix?

    belt tension or the set screw on the pulley.
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  5. Ocsff
    Post

    Unresolved EXTRUDER GEAR AND MOTOR GRINDING

    yes but you may need to lengthen the wires. All the motors are interchangeable.
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  6. Ocsff
    Post

    Unresolved doesnt heat up.

    Mark is very good at trouble shooting the printers. I have faith he will get you printing again.
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  7. Ocsff
    Post

    Unresolved Glass bed Upgrades

    check that your bed mounting magnets are seated all the way. Most common cause of out of level bed that I have found.
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  8. Ocsff
    Post

    Unresolved EXTRUDER GEAR AND MOTOR GRINDING

    Mark is on the right track . Also check the wiring While refurbishing printers for ROBO3D I have found a few with this same issue that were...
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  9. Ocsff
    Post

    Unanswered how often will i have to change the robo 3d r1+ parts?

    Nicely put !
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  10. Ocsff
    Post

    Unresolved Auto-Leveling triggering in mid-air

    Check your z axis switches and make sure the carriage is level. usual cause is z axis switch not seated
    Post by: Ocsff, Sep 22, 2016 in forum: Troubleshooting
  11. Ocsff
    Post

    Excellent customer service - Printed Solid

    Just a shout out to Matt at printed solid. I ordered the Titan extruder from him and I didn't read the full discription of what was included. I...
    Post by: Ocsff, Sep 19, 2016 in forum: Off Topic
  12. Ocsff
    Post

    Multiple Robo 3D R1 with mods for sale (San Diego, CA)

    Sorry no shells , only working printers
    Post by: Ocsff, Sep 19, 2016 in forum: United States of America
  13. Ocsff
    Thread

    Multiple Robo 3D R1 with mods for sale (San Diego, CA)

    Hey guys I have multiple Robo 3D R1 printers for sale. I worked for Robo 3D part time for a short while as a repair technition and refurbished...
    Thread by: Ocsff, Sep 13, 2016, 5 replies, in forum: United States of America
  14. Ocsff
    Post

    R1 to R1+ heated bed.

    Yes , I just forgot to turn off Cap lock. Was designing on Inventor and putting text on a project. Sorry for the educate mistake I also am an...
    Post by: Ocsff, Sep 13, 2016 in forum: Mods and Upgrades