1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by WheresWaldo

  1. WheresWaldo
    Post

    Python 2.7?

    Just waiting on an interface replacement. The rest appears to be working.
    Post by: WheresWaldo, Aug 17, 2019 at 3:57 AM in forum: General Questions
  2. WheresWaldo
    Post

    Unresolved Need a little help with some lifting.

    Also a super clean bed helps, and I mean cleaned using an alcohol wipe. I have had luck with both super clean (which can be tedious to maintain)...
    Post by: WheresWaldo, Aug 12, 2019 at 9:17 AM in forum: Troubleshooting
  3. WheresWaldo
    Post

    Solved R1 + bed not heating up.

    Hard to say without more details, but it could be a failing MOSFET on the RAMPS board, if I were to venture a guess in a vacuum.
    Post by: WheresWaldo, Aug 6, 2019 in forum: Troubleshooting
  4. WheresWaldo
    Post

    Unanswered Anyone have a heat pad that they would recommend? Building a new bed for R1+

    When I had my R1, I swapped the bed for an Aluminum plate and then used a heat pad from...
    Post by: WheresWaldo, Aug 4, 2019 in forum: General Questions
  5. WheresWaldo
    Post

    New bed leveling idea..

    Just an example, I hadn't printed anything on my R2 is over two months. But this week I needed an rPi case, CC2531 Sniffer cover, electronics box...
    Post by: WheresWaldo, Aug 4, 2019 in forum: Projects
  6. WheresWaldo
    Post

    New bed leveling idea..

    There is a version that works already posted in the forums. Yes, it breaks the Robo software (specifically the leveling wizard), because it does...
    Post by: WheresWaldo, Aug 4, 2019 in forum: Projects
  7. WheresWaldo
    Post

    Tools, jigs and other useful stuff you have printed on your Robo3D printer

    Naturally
    Post by: WheresWaldo, Aug 4, 2019 in forum: Show and Tell
  8. WheresWaldo
    Post

    Tools, jigs and other useful stuff you have printed on your Robo3D printer

    I basically works like all tensiometers, in this case the spoke sits on the two outside bolt heads, while the third tries to deform the spoke, you...
    Post by: WheresWaldo, Aug 3, 2019 in forum: Show and Tell
  9. WheresWaldo
    Post

    Tools, jigs and other useful stuff you have printed on your Robo3D printer

    This is a derivative of the tool DT-Swiss sells.
    Post by: WheresWaldo, Aug 2, 2019 in forum: Show and Tell
  10. WheresWaldo
    Post

    Tools, jigs and other useful stuff you have printed on your Robo3D printer

    You do know what it is, correct? Once you build your wheel, you would use this tool to verify that the spoke tension is nearly identical on all...
    Post by: WheresWaldo, Aug 2, 2019 in forum: Show and Tell
  11. WheresWaldo
    Post

    Error detected

    Usually it is because you are heating the bed near it's physical limit and it took too long to get there. On my particular R2 my physical limit...
    Post by: WheresWaldo, Jul 29, 2019 in forum: Troubleshooting
  12. WheresWaldo
    Post

    1.5.0.6642 and ROBO3DR1AUTOV4 on R1 printer

    An upgrade to lead screws is one of the better ones you can do. The threaded rods on early R1's where not very accurate, nor very straight either,...
    Post by: WheresWaldo, Jul 10, 2019 in forum: General Questions
  13. WheresWaldo
    Post

    1.5.0.6642 and ROBO3DR1AUTOV4 on R1 printer

    There are a couple of Community versions on here, look for the sticky thread on Marlin 1.1.9
    Post by: WheresWaldo, Jul 9, 2019 in forum: General Questions
  14. WheresWaldo
    Post

    1.5.0.6642 and ROBO3DR1AUTOV4 on R1 printer

    It an R1 but could be a PLUS, the Firmware version doesn't tell us anything since Robo renumbered the Open Source Marlin firmware versions. A...
    Post by: WheresWaldo, Jul 9, 2019 in forum: General Questions
  15. WheresWaldo
    Post

    My solution for the IR sensor / Buildtak probe failures

    Jeff, that would be typical of the leveling method enabled by the Robo firmware. I would say that 0.1 mm is about as accurate as you will ever get...
    Post by: WheresWaldo, Jul 8, 2019 in forum: Troubleshooting