1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 10
  1. JuniorGamingTime
    Post

    Solved Z Offset Issues

    **Just got my printer** So like the title says im trying to set the Z offset i use the code M565 Z-1.1 like in the "Novice Expert" Youtube video...
    Post by: JuniorGamingTime, Jun 6, 2018 in forum: Troubleshooting
  2. Mattfay72
    Post

    Solved Z-offset issue

    My new refurb Robo 3d R1 plus had first layer problems. Printing to close to the bed using Simplify3D and Octoprint. I read through many of the...
    Post by: Mattfay72, Apr 23, 2017 in forum: Troubleshooting
  3. Zdot
    Post

    Unanswered Z offset and bed leveling questions

    I am trying to print a 215 X 215 mm piece in ABS so having a precisely leveled print bed seems to be key for success. My search in this forum for...
    Post by: Zdot, Mar 25, 2016 in forum: Troubleshooting
  4. Dave (with an echo)
    Post

    Solved installed a E3dv6 head and z offset is way out

    Hi, I've installed a e3dv6 head on my robo 3d. The zoffset is way out. It starts to print about 10cm from the bed I tried to fix it with auto...
    Post by: Dave (with an echo), Apr 14, 2016 in forum: Troubleshooting
  5. aznhlfan
    Post

    Cura Ignoring Z-Offset after Auto Level Robo R1+

    I downloaded Cura 15.04, followed Mike Kelly's set-up instructions, but after running th 9 point auto level the printer ignores my M565 Z setting...
    Post by: aznhlfan, Jun 28, 2017 in forum: General Questions
  6. Oisin
    Post

    Unresolved Z-axis problems.

    Hi guys. I've come here to try to fix this quite a few times before but never got to the bottom of it since it's a weird issue. My printer never...
    Post by: Oisin, Sep 21, 2016 in forum: Troubleshooting
  7. WheresWaldo
    Post

    Answered Bottom Layer squish

    You need to increase the Z offset adjusting M565 in your startup code
    Post by: WheresWaldo, Mar 14, 2018 in forum: Troubleshooting
  8. mark tomlinson
    Post

    Solved Prints have sharp edge

    Adjust the M565 z offset less negative is closer to the bed.
    Post by: mark tomlinson, Feb 1, 2017 in forum: Troubleshooting
  9. danzca6
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Remember that z offset is no longer set using M565 with this version.
    Post by: danzca6, Nov 2, 2016 in forum: Mods and Upgrades
  10. mark tomlinson
    Post

    Community Favorite E3D v6 Information and Installation Guide

    There are a lot of posts about Z offset :) Startup GCode: G28; M565 Z-1.0; G29; Adjust the M565 as needed. 1.0 mm is just a starting point.
    Post by: mark tomlinson, Jan 10, 2021 in forum: Mods and Upgrades
  11. Greg Howard
    Post

    Solved First few layers not printing correctly

    What does the M565 z-10 offset do? does a '-' bring the nozzle up or down?
    Post by: Greg Howard, Jan 5, 2017 in forum: Troubleshooting
  12. mark tomlinson
    Post

    Answered S3D auto level issues

    Without an M565 you are not applying a Z offset to the autoleveling mechanism. The M565 is not a global Z offset it is a Z offset APPLIED to the Z...
    Post by: mark tomlinson, Apr 23, 2017 in forum: Troubleshooting
  13. Geof
    Post

    Solved Uneven First Layer on one side of bed

    Add the M565 Z-.80; initial z offset gcode to the start up script. Remove it from the global.
    Post by: Geof, Nov 8, 2016 in forum: Troubleshooting
  14. mark tomlinson
    Post

    Answered First layer is too for from the platform.

    If the slicer does not use M565 it is not affecting the Z offset for the autoleveling calculations.
    Post by: mark tomlinson, Jul 27, 2017 in forum: Troubleshooting
  15. Shigemal
    Post

    Solved Printing shows Z offset

    Thanks Mark I have reviewed thread of M565 issue . And negative z-offset of Robo3D mechanism is unique. regards
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  16. mark tomlinson
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    What Z offset do you have defined for the M565 command in your startup GCode tab (in the process settings).
    Post by: mark tomlinson, Apr 20, 2016 in forum: Troubleshooting
  17. mark tomlinson
    Post

    Answered I have all the problems. Anyone have solutions?

    Show us what you have for the autoleveling Z offset in your startup GCode (the M565 command)
    Post by: mark tomlinson, Apr 21, 2018 in forum: Troubleshooting
  18. mark tomlinson
    Post

    Answered First layer of PLA wont stick

    Try changing this: M565 Z-1.05; set the offset for auto-leveling to this: M565 Z-0.8; set the offset for auto-leveling and see if it sticks better
    Post by: mark tomlinson, Aug 19, 2017 in forum: Troubleshooting
  19. WheresWaldo
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Not M565, that was deprecated, you have to use M851 if you need a Z offset with MESH.
    Post by: WheresWaldo, Jan 30, 2018 in forum: Mods and Upgrades
  20. mark tomlinson
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    That is an excellent point as well :) You need an M565 in there... M565 Z-1.0 ; set the offset for auto-leveling mechanism right before the G29
    Post by: mark tomlinson, Jan 11, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 200 Next >
Search Again
Page 1 of 10