1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 10
  1. Geof
    Post

    Solved Prints come out slightly angled or stretched

    Glad to hear it ! Happy printing
    Post by: Geof, Apr 21, 2019 in forum: Troubleshooting
  2. Geof
    Post

    Solved Prints come out slightly angled or stretched

    I’d start with aligning the gantry https://www.thingiverse.com/thing:2532723
    Post by: Geof, Apr 21, 2019 in forum: Troubleshooting
  3. Geof
    Post

    Solved R1+ Shutting off

    http://community.robo3d.com/index.php?threads/taking-the-r1-ramps-and-rewiring-to-make-generic-ramps-work.8356/
    Post by: Geof, Apr 21, 2019 in forum: Troubleshooting
  4. Geof
    Post

    Artillery 3D Sidewinder X1

    Reserved
    Post by: Geof, Apr 18, 2019 in forum: Off Topic
  5. Geof
    Post

    Artillery 3D Sidewinder X1

    Reserved
    Post by: Geof, Apr 18, 2019 in forum: Off Topic
  6. Geof
    Post

    Artillery 3D Sidewinder X1

    Now for some pictures of prints- initially I was getting what appeared to be over extrusion and banding : to fix this I double checked the belt...
    Post by: Geof, Apr 18, 2019 in forum: Off Topic
  7. Geof
    Thread

    Artillery 3D Sidewinder X1

    Hello All! Artillery 3D asked if I would like to recieve a printer to show everyone here and on my social media accounts. I typically say no to...
    Thread by: Geof, Apr 18, 2019, 6 replies, in forum: Off Topic
  8. Geof
    Post

    Solved Filament not extruding even with new extruder

    http://community.robo3d.com/index.php?threads/extruder-tensioner-arm.19892/#post-120183 Bottom of the thread is the Robo supplied one
    Post by: Geof, Apr 15, 2019 in forum: Troubleshooting
  9. Geof
    Post

    Solved Filament not extruding even with new extruder

    There is a cad file for that widget in the R2 section somewhere assuming they are the same ;)
    Post by: Geof, Apr 15, 2019 in forum: Troubleshooting
  10. Geof
    Post

    New source for reprapdiscount XXL LCD controller?

    Should be plug and play but will likely need a new case printed.
    Post by: Geof, Apr 9, 2019 in forum: Mods and Upgrades
  11. Geof
    Post

    PEI Sheets precut with 3m

    Very welcome, I'm in talks with Buildtak and Wham Bam Systems (flex plate option that is fair price) about the R1 series. Stay tuned!
    Post by: Geof, Apr 9, 2019 in forum: Mods and Upgrades
  12. Geof
    Post

    Air Printing 10mm above the bed

    Hi @Johannbv have you cleaned the IR sensor to ensure its not false triggering?
    Post by: Geof, Apr 9, 2019 in forum: Troubleshooting
  13. Geof
    Post

    My printer keeps stopping mid print

    I'd start with reflashing your image to the R2's Raspberry Pi. If that doesn't fix it then I'd look to see if another slicer (or gcode causes the...
    Post by: Geof, Apr 9, 2019 in forum: Troubleshooting
  14. Geof
    Post

    Tried to install OP plugin Octoprint Anywhere and got this update suggestion

    Was not banned. Account is still an active account. He did have quite the problem with me, in which there was a conversation with Robo Admins...
    Post by: Geof, Apr 9, 2019 in forum: Troubleshooting
  15. Geof
    Post

    Unresolved Grinding noise while printing

    I just take those metal clips off and put them in a drawer until I need to remove the glass- then pop them back on and remove them :D. A little...
    Post by: Geof, Apr 8, 2019 in forum: Troubleshooting
  16. Geof
    Post

    Unresolved Grinding noise while printing

    Sounds like one of your binder clips is rattling. if you take the metal "prongs" off the clips or touch them while its making the noise and it...
    Post by: Geof, Apr 8, 2019 in forum: Troubleshooting
  17. Geof
    Post

    Miniature Print Quality

    Good plan! And a cheap test to perform.
    Post by: Geof, Apr 8, 2019 in forum: General Questions
  18. Geof
    Post

    3D Printed Female and Male Model

    It appears a lot of the issues are coming from the part separating from the support structure? Is that true? If so the setting you want to look...
    Post by: Geof, Apr 8, 2019 in forum: Troubleshooting
  19. Geof
    Post

    Miniature Print Quality

    A stable base is important. you can brace the legs if moving the machine to the floor helps your issue. It would really have to be rockin I'd...
    Post by: Geof, Apr 8, 2019 in forum: General Questions
  20. Geof
    Post

    3D Printed Female and Male Model

    If you cant please send me a private message and we can work out how to get them posted for you.
    Post by: Geof, Apr 8, 2019 in forum: Troubleshooting
Showing results 21 to 40 of 192 Next >
Search Again
Page 2 of 10