1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. BronStoppable
    Post

    Unresolved Still can’t use change filament button

    Example A
    Post by: BronStoppable, Jul 18, 2020 in forum: Troubleshooting
  2. BronStoppable
    Thread

    Unresolved Still can’t use change filament button

    So I’m using a Robo R1 plus with a lcd scree and marlin. Whenever I click on the printer to change filament mid print, I’d does the movement and...
    Thread by: BronStoppable, Jul 18, 2020, 2 replies, in forum: Troubleshooting
  3. BronStoppable
    Post

    Solved Can someone help explain why this is happening?

    So after fiddling with it, i found out The bulk of the problem seems to be that my extruder tension doesn’t say the same. I’m guessing it loses as...
    Post by: BronStoppable, Jun 25, 2020 in forum: Troubleshooting
  4. BronStoppable
    Post

    Solved Can someone help explain why this is happening?

    You are correct about the fan. The hot end one runs once it’s on i mean. I can get you to print. It just has been leaving lines lately. And I...
    Post by: BronStoppable, Jun 23, 2020 in forum: Troubleshooting
  5. BronStoppable
    Post

    Solved Can someone help explain why this is happening?

    I’ve soaked the nozzle in acetone and used .4mm needles on it. I’ll google what seasoning it is. with the tpu it wasn’t AS bad but you can see...
    Post by: BronStoppable, Jun 23, 2020 in forum: Troubleshooting
  6. BronStoppable
    Thread

    Solved Can someone help explain why this is happening?

    I have a robo r1 with some upgrades. But lately when I print these separation lines have been happening. Not everytime but randomly. This photo is...
    Thread by: BronStoppable, Jun 23, 2020, 11 replies, in forum: Troubleshooting
  7. BronStoppable
    Post

    Answered Can’t change filament

    [MEDIA]
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  8. BronStoppable
    Post

    Answered Can’t change filament

    [MEDIA] sorry my mic was off lol and it’s actually a qtip to replace the screw that engages the home switch as it broke off the carriage by the...
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  9. BronStoppable
    Post

    Answered Can’t change filament

    [MEDIA] as you can see once it clip, it slides then makes a noise, stops but once it starts again it’s no longer in line with the original print.
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  10. BronStoppable
    Post

    Answered Can’t change filament

    It makes a clicking stepper noise as it moves to the left before it hits the tab which is why i thought it was the plate size. Like it expects...
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  11. BronStoppable
    Post

    Answered Can’t change filament

    Just tried, even without filament it didn’t line back up after continuing the print
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  12. BronStoppable
    Post

    Answered Can’t change filament

    Yea I have the quick change add on so it just pops out, switches and then goes back. How would i do that? It releases the filament once it stops...
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  13. BronStoppable
    Post

    Answered Can’t change filament

    I don’t think it’s that, it stays in position once it reaches the stopper.
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  14. BronStoppable
    Thread

    Answered Can’t change filament

    Hey, so whenever i click change filament mid print, everything seems to work fine until i restart it. Once it slides to go back and printing it’s...
    Thread by: BronStoppable, Nov 13, 2019, 14 replies, in forum: Troubleshooting
  15. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Correct, if I use the change filament setting it happens every time but other than that prints and moves normally which is why I thought it was my...
    Post by: BronStoppable, Apr 8, 2019 in forum: Troubleshooting
  16. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Yea i did it right from home and when it got over to the far left stepper it made the noise as if it was trying to go farther, the popped out the...
    Post by: BronStoppable, Apr 7, 2019 in forum: Troubleshooting
  17. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Thanks for responding. I don’t think the steppers are messed up or anything as they only make the noise when part of a print is out of bounds ie:...
    Post by: BronStoppable, Apr 6, 2019 in forum: Troubleshooting
  18. BronStoppable
    Thread

    Answered Changing Filament Mid print Offset?

    Hi, So whenever I use the change filament button on the lcd, it shifts over, makes a grind noise(like when the x goes to far) as it hits the...
    Thread by: BronStoppable, Apr 6, 2019, 7 replies, in forum: Troubleshooting
  19. BronStoppable
    Post

    Answered Help! Prints suddenly brittle

    lol yea I usually put a few drops of oil in it before I print. But i will try both the things you said, thank you again
    Post by: BronStoppable, Nov 16, 2017 in forum: Troubleshooting
  20. BronStoppable
    Post

    Answered Help! Prints suddenly brittle

    I have a oilier clipped on the filament right before it goes into the extruder. I actually think based on what I've read its under extruding but I...
    Post by: BronStoppable, Nov 16, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2