1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 7
  1. OBI WAN KEN0B1
    Thread

    Solved Print bed off center

    Hi Everybody Just got my New R1plus the other day and i have noticed that my print bed is not centered. When it starts to print something big it...
    Thread by: OBI WAN KEN0B1, Oct 10, 2016, 5 replies, in forum: Troubleshooting
  2. moelafi
    Post

    Unresolved bed center problem

    hi guys, we all know that the robo r1 plus has an issue where it prints on the back out of the defined print area, is there a way to fix that...
    Post by: moelafi, Oct 7, 2016 in forum: Troubleshooting
  3. Europa
    Post

    Question about R1 design: why is the Y-axis belt off-center?

    I'm on a kick to decrease lash/increase rigidity of my R1+, and I'm curious - from a design/engineering standpoint - why the Y-axis belt is...
    Post by: Europa, Nov 16, 2020 in forum: General Questions
  4. Drmike
    Post

    Unanswered Z axis offset way off

    I've finally got a few things working, but when the device goes to auto level it is way, way off. I've attached a picture of where the z axis...
    Post by: Drmike, Feb 13, 2016 in forum: Troubleshooting
  5. robocad
    Post

    Unanswered Print keeps pulling PEI sheet off of bed, what can i do

    Ive been printing a wide print in PETG, it takes up most of the buildspace, but its not very tall, however its tall enough that it lifts off the...
    Post by: robocad, May 28, 2016 in forum: Troubleshooting
  6. gearprinter
    Post

    Solved Gantry Brace (?) Broke Off + Other Issues

    Robo 3D R1+ E3D nozzle 1.75mm 0.4 PLA - Hello, 1) I broke the gantry brace on my 3d printer while trying to tighten a screw. Any idea where I...
    Post by: gearprinter, Apr 2, 2021 in forum: Troubleshooting
  7. PTIschool
    Post

    Unanswered Reseating Bed Magnets

    I have replaced the glass bed on my printer and set the magnets on the bottom of the glass with the 2 part adhesive that is provided with it, but...
    Post by: PTIschool, Sep 4, 2021 in forum: Troubleshooting
  8. J_Man
    Post

    Solved Bent Table Bed

    I got the Robo C2 this week and finally got to try it this weekend. I went with the idea to try and plug the USB stick to load a model. I figure...
    Post by: J_Man, Apr 9, 2017 in forum: Troubleshooting
  9. Lance Weston
    Post

    Updated Bed temp table

    I use 4mm microporous glass beds. I found that there was a significant drop in temp across the glass using a thermal gun. I stepped through the...
    Post by: Lance Weston, Aug 11, 2022 in forum: Mods and Upgrades
  10. Lee
    Post

    Heated Bed Heater Size R1 Plus

    I have noticed that the shipping R1Plus heated bed shows the following. With temperature set to 100, the center of the bed show 100 but out where...
    Post by: Lee, Feb 6, 2016 in forum: General Questions
  11. Geof
    Post

    Answered Center to Center distance for the Y rods on R1 +Plus

    I took the bed holder off my r1+ and am getting 224/225 center to center
    Post by: Geof, May 21, 2016 in forum: General Questions
  12. Mr Smiley
    Post

    Unanswered AutoLevel command moving bed too far (grinding)

    When I first got my printer I had the same problem, which turned out to be the print bed cable. I also found the it was printing back from center,...
    Post by: Mr Smiley, Mar 14, 2016 in forum: Troubleshooting
  13. Thomas E. Foss
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    Question: The R1+ has a predetermined build area and when I print a circular item in the center of the build area on Matter Control it ends up...
    Post by: Thomas E. Foss, Apr 20, 2021 in forum: Mods and Upgrades
  14. mark tomlinson
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    There are a massive amount of threads on this going back ... forever....
    Post by: mark tomlinson, Apr 21, 2021 in forum: Mods and Upgrades
  15. Curtis Wolfe
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    I'm sorry. Not the Z off set. It's not initiating the print in the center of the bed. It's trying to print in the front left corner where its...
    Post by: Curtis Wolfe, Mar 17, 2017 in forum: Mods and Upgrades
  16. TaigaChat
    Post

    Shoutbox Archive

    Dec 7, 2018 1:12 PM - Mark Ostrander: new member..new robo r1+ user. Y adjustment seems off. Prints outside the rear "area" losing adhesion to bed...
    Post by: TaigaChat, Dec 7, 2018 in forum: Archive
  17. Curtis Wolfe
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    Today I decided to go back to Cura and mess around. I figured out why it was printing off of the center of the bed. I started printing a...
    Post by: Curtis Wolfe, Mar 19, 2017 in forum: Mods and Upgrades
  18. SteveDjarrell
    Post

    Robo 3D R2 Not Upgrading to roboOS 2.0

    So I was pretty excited to see a new release today for the ROBO OS. I loaded it up, reset my Z offset and whammo, my Auto-leveling is way off. I...
    Post by: SteveDjarrell, Mar 12, 2018 in forum: Software
  19. mark tomlinson
    Post

    Unanswered Downloaded file printing an inch back on the bed

    The markings on the bed are decorations, frankly. If it happens to actually line up with the heater it is more happenstance than planning. You...
    Post by: mark tomlinson, Jun 11, 2016 in forum: Troubleshooting
  20. mark tomlinson
    Post

    Solved Prints are about an inch off

    You can position the model anywhere on the bed you like in most slicers so if it really is too far off the center of the heater, just adjust it in...
    Post by: mark tomlinson, Jan 13, 2019 in forum: Troubleshooting
Showing results 1 to 20 of 129 Next >
Search Again
Page 1 of 7