1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. BJS227
    Post

    Used Robo R2 for sale

    NO reasonable offer will be declined. Reduced price $550
    Post by: BJS227, May 21, 2021 in forum: General Questions
  2. BJS227
    Thread

    Used Robo R2 for sale

    Used Robo R2 3D Printer, original owner, great condition, lots of extras, octoprint, power supply in great condition, . I install led lights...
    Thread by: BJS227, May 3, 2021, 2 replies, in forum: General Questions
  3. BJS227
    Post

    connection issue

    OK firmware has been updated without any issue! The an issue but with a different reason is popin up as description in entry #1. check out pic....
    Post by: BJS227, Dec 11, 2020 in forum: Troubleshooting
  4. BJS227
    Post

    connection issue

    The file printing I've printed many times before. So that leads me to think I have a hardware issue vs software. Anyway Cura: Cura is 2.5...
    Post by: BJS227, Dec 9, 2020 in forum: Troubleshooting
  5. BJS227
    Post

    connection issue

    we are using Cura 2.5.0. Where do I find the firmware number? The file we are printing we have printed many times in the past. We also use...
    Post by: BJS227, Dec 3, 2020 in forum: Troubleshooting
  6. BJS227
    Thread

    connection issue

    Having trouble with a "connection interrupted" When using the fine tune offset wizard the extruder goes through its 9 leveling steps with the bed...
    Thread by: BJS227, Dec 2, 2020, 24 replies, in forum: Troubleshooting
  7. BJS227
    Thread

    print quality is gone

    Check out the pic. Does anyone what would cause the printer quality to look so bad? Just overnight it did this. Thoughts? TIA!
    Thread by: BJS227, Aug 10, 2020, 3 replies, in forum: Troubleshooting
  8. BJS227
    Post

    Finishing Goober

    sweet, worked awesome. thank you very much!
    Post by: BJS227, Jun 10, 2020 in forum: Troubleshooting
  9. BJS227
    Post

    Finishing Goober

    So Mark paste your exact code above where my red line is. also leaving the two lines that are already there, Correct?
    Post by: BJS227, Jun 9, 2020 in forum: Troubleshooting
  10. BJS227
    Post

    Finishing Goober

    in octoprint i have in the "after print job completes": ; turn off heaters M104 S0 M140 S0 ; turn off fans M107 ; move bed down 10mm G91 G1 Z10...
    Post by: BJS227, Jun 9, 2020 in forum: Troubleshooting
  11. BJS227
    Post

    Finishing Goober

    How do i do that? Do you use cura?
    Post by: BJS227, Jun 8, 2020 in forum: Troubleshooting
  12. BJS227
    Thread

    Finishing Goober

    Take a look at the pic. when all my prints finish lately it leaves a goober where the extruder stops. Any idea what i need to change in setting...
    Thread by: BJS227, Jun 8, 2020, 13 replies, in forum: Troubleshooting
  13. BJS227
    Post

    filament not loading

    Got it running again, thanks guys!
    Post by: BJS227, Jun 8, 2020 in forum: Troubleshooting
  14. BJS227
    Post

    filament not loading

    Thank you Lance, i inspected the cable and found a small break on one side so looks like I'm changing a ribbon cable! I looked on partsbuild.com...
    Post by: BJS227, May 18, 2020 in forum: Troubleshooting
  15. BJS227
    Thread

    filament not loading

    This will not let me upload a video. But when i tried install some new pla the motor jerks back and forth like its trying to move in one...
    Thread by: BJS227, May 14, 2020, 10 replies, in forum: Troubleshooting
  16. BJS227
    Thread

    help with first layer on section of bed

    Check out the pic. We're have an issue with one part of the print not sticking (front left as facing machine) to the heated bed then warping just...
    Thread by: BJS227, Jan 8, 2020, 2 replies, in forum: Troubleshooting
  17. BJS227
    Post

    ColorFabb PLA issue

    im sorry. Look like my pic didnt upload in the first post. Would explain your question. LOL LMK Thank you in advance![ATTACH]
    Post by: BJS227, Oct 22, 2019 in forum: Troubleshooting
  18. BJS227
    Thread

    ColorFabb PLA issue

    OK, I’ve been printing with ROBO Pla with much success and now with the limited quantities I have switch to ColorFabb brand and have been having...
    Thread by: BJS227, Oct 22, 2019, 3 replies, in forum: Troubleshooting
  19. BJS227
    Thread

    Error detected

    Anyone know what this means exactly? Thank you! [ATTACH]
    Thread by: BJS227, Jul 28, 2019, 2 replies, in forum: Troubleshooting
  20. BJS227
    Post

    Skirt print sticking to Buildtak bed

    Is there a setting in Cura or Simplified 3d that could increase the zoffset on intial layer?
    Post by: BJS227, Jul 24, 2019 in forum: Troubleshooting
Showing results 1 to 20 of 43 Next >
Search Again
Page 1 of 3