1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. John in MS
    Thread

    Unresolved Extruder stepper cable fail (Design flaw?)

    My Robo Plus has been down a majority of time for about a month now with extruder stepper issues. I began by thinking it was a motor then went to...
    Thread by: John in MS, Jul 3, 2016, 2 replies, in forum: Troubleshooting
  2. John in MS
    Thread

    Solved New Ramps Layout Help

    [IMG] [IMG] Above is the old Ramps, Below the new. I need to know where the blue/gray wires go and the thermistor ones also.. New one always...
    Thread by: John in MS, Jun 17, 2016, 41 replies, in forum: Troubleshooting
  3. John in MS
    Thread

    Unanswered Strange noise just started, aka Stepper drive from Hades

    [MEDIA] I hope this is showing to allow you to hear the sound. I just installed a new extruder fan Friday and it was working great until...
    Thread by: John in MS, Jun 6, 2016, 28 replies, in forum: Troubleshooting
  4. John in MS
    Thread

    Unresolved Extruder fan not working

    My extruder jammed tonight on my R1+ and I was able to clear it. Putting the filament back in I noticed the little fan on the find wasn't...
    Thread by: John in MS, May 27, 2016, 10 replies, in forum: Troubleshooting
  5. John in MS
    Thread

    PLA Found ProMolt PLA on Amazon. Any good?

    Looking for affordable PLA I normally go to Hatchbox. But I found ProMolt PLA. running about two dollars cheaper. Anybody use this? And the...
    Thread by: John in MS, May 13, 2016, 9 replies, in forum: Printing Filament
  6. John in MS
    Thread

    Solved Affordable options for J-head replacement

    [IMG] Over these seven months of having this printer I have had little luck with hotends. I have had clogs, broke thermistors and torn wires on...
    Thread by: John in MS, Apr 18, 2016, 28 replies, in forum: General Questions
  7. John in MS
    Thread

    Unanswered Is it a clog or my stepper motor?

    I hope my problem can be resolved easily as I just hit my six months of warranty coverage. I just installed a new extruder this week. It was...
    Thread by: John in MS, Apr 7, 2016, 2 replies, in forum: Troubleshooting
  8. John in MS
    Thread

    Will the Robo R1 handle a model 8.75 tall with a oiler on top?

    I am 4 hours into a print that will in the end be 8.75 inches tall. My present configuration has an oiler on top on the extruder which is about...
    Thread by: John in MS, Apr 3, 2016, 10 replies, in forum: General Questions
  9. John in MS
    Thread

    Unanswered Anyone ever save a print after a power loss?

    Well I was here at the office and I get a call from my son who is on spring break. Seems he tripped a breaker in the garage and my Robo stopped 15...
    Thread by: John in MS, Mar 24, 2016, 4 replies, in forum: General Questions
  10. John in MS
    Thread

    Lines in Final print on Medium Quality using Cura

    [IMG] Last week I was having the problem of "pillowing" so I increased the Top layers, and that worked fine for a few prints. I have not...
    Thread by: John in MS, Mar 9, 2016, 8 replies, in forum: General Questions
  11. John in MS
    Thread

    Unresolved Bubbles on final product

    Just wondering what I can do to stop these bubbles in PLA? My recipe in Mattercontrol is: Quality High, 15% infill, Curaengine, Extruder 220, Bed...
    Thread by: John in MS, Feb 28, 2016, 6 replies, in forum: Troubleshooting
  12. John in MS
    Thread

    Unanswered STL file help

    [IMG] I was going to ask if anyone could help with a problem I have. I have downloaded the file above down from the Sketchup 3d warehouse. It's...
    Thread by: John in MS, Feb 21, 2016, 3 replies, in forum: General Questions
  13. John in MS
    Thread

    Unanswered How would I check voltage to the extruder?

    I just got off the phone with help desk. My hot end will not heat up and I am getting the Printer is stopped due to errors Fix the errors and use...
    Thread by: John in MS, Feb 5, 2016, 2 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 33 of 33
Search Again
Page 2 of 2