1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 7
  1. mark tomlinson
    Post

    Hello SoCal

    As for the heated bed, the style of heater they use is not going to distribute the heat evenly. So as you have found the center will be about...
    Post by: mark tomlinson, May 27, 2016 in forum: United States of America
  2. Joe Coyne
    Post

    Unresolved Robo R1+ prints not centering on y axis as shown in Mattercontrol

    Was reading through this thread because my large print was fitting on the 3d view bed, but the bottom ~1/10 of my print was being cut off the...
    Post by: Joe Coyne, Jul 13, 2016 in forum: Troubleshooting
  3. Curtis Wolfe
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    So, I have the LCD installed, and Cura installed on the PC. Three things when I send the print to the printer from the LCD screen. It doesn't go...
    Post by: Curtis Wolfe, Mar 17, 2017 in forum: Mods and Upgrades
  4. KTMDirtFace
    Post

    Best carriage design

    I mean a little bit, but I dont even use a heated bed anymore. so I don't care. ( aluminum bed with lexan now ).. If I put a heater on its going...
    Post by: KTMDirtFace, Jun 10, 2017 in forum: Mods and Upgrades
  5. Jason Hopkins
    Post

    Unanswered Question on Y axis, time to learn some new stuff

    Sorry, for delay in response. I have gotten it printing better and taken pictures I need to post still. But I am using the gfx as a refernece to a...
    Post by: Jason Hopkins, Oct 17, 2021 in forum: Troubleshooting
  6. Ed Ferguson
    Post

    Unresolved Prints slipping on PEI surface

    Mark - The settings I'm currently using are not causing warping. The higher bed temp has really helped me to achieve a good bond to the bed....
    Post by: Ed Ferguson, Nov 9, 2016 in forum: Troubleshooting
  7. SteveDjarrell
    Post

    Latest Update and G36

    Hi all, I had issues with the last update. I got to a point I can use the machine but I really want to like the Bi-Linear Bed Leveling. So I set...
    Post by: SteveDjarrell, Mar 14, 2018 in forum: Software
  8. mark tomlinson
    Post

    Unresolved X-Offset Broken

    1) Is the X stepper trying to turn? You would hear a hum or see the belt twitch since the X stepper is right there above the bed on the cross-bar....
    Post by: mark tomlinson, Jan 12, 2020 in forum: Troubleshooting
  9. zeroprod
    Post

    Solved Y-axis offset adjustment

    Hello Jeff, I have had my Robo R1 Plus for only 3 months and I may be new to 3d printing but I have noticed that in MatterControl when I start a...
    Post by: zeroprod, Mar 21, 2018 in forum: Troubleshooting
  10. Thomas E. Foss
    Post

    Mods and experiences with our Robo 3D R1+ (1st Printer)

    OK, I changed the bed size to 225 and recompiled the code then uploaded it. Tried home for the Y axis and the new home for the Y axis is bed all...
    Post by: Thomas E. Foss, Apr 12, 2021 in forum: Mods and Upgrades
  11. Joe Coyne
    Post

    Unresolved Robo R1+ prints not centering on y axis as shown in Mattercontrol

    Fudging with the "Print Center" numbers did not help. I opened my STL in Cura, and the print was centered correctly. I let my Robo print the...
    Post by: Joe Coyne, Jul 15, 2016 in forum: Troubleshooting
  12. jscottb
    Post

    R2 received and in production!

    I have no issues with the bed being off and am fine with it as long as it consistent, and it seems to be. The octoprint profiles have been changed...
    Post by: jscottb, Sep 19, 2017 in forum: Show and Tell
  13. supercazzola
    Post

    Door Scratches

    Thanks for your post. Mine appears to be happening in front of my eyes during prints. I see shaved acrylic accumulating in the center of the...
    Post by: supercazzola, Jul 27, 2017 in forum: General Questions
  14. Geof
    Post

    Solved Printing goes off axis mid print

    So the bed is the Y axis. Under the bed (if you raise the extruder and lift up on the glass it will lift off its magnets so you can look under...
    Post by: Geof, Apr 10, 2017 in forum: Troubleshooting
  15. HelmutK
    Post

    Unresolved Robo R1+ prints not centering on y axis as shown in Mattercontrol

    Normally I would ignore this but the outline markings on the glass bed do align closely with where the actual heater pad is underneath. So for...
    Post by: HelmutK, Mar 30, 2016 in forum: Troubleshooting
  16. Cindy C
    Post

    R2 Probing error . self leveling

    4 times in a row I have had the hot end dig into the bed during self leveling either in the center back or right back. I have re-greased the z...
    Post by: Cindy C, Feb 18, 2019 in forum: Troubleshooting
  17. curiousjoi
    Post

    Unresolved X-Offset Broken

    No noise from the x stepper and it doesn't move at all
    Post by: curiousjoi, Jan 12, 2020 in forum: Troubleshooting
  18. mark tomlinson
    Post

    Partially Solved Calibrating seems to be off on Y axis

    ?Lines? If you mean the actual heated area, OK, if you mean the graphic on the build plate -- it is meaningless. A pretty design graphic, not...
    Post by: mark tomlinson, May 22, 2016 in forum: Troubleshooting
  19. jediknight0
    Post

    PEI Print Bed

    I tried using clips... it didn't work. Even though my piece of PEI was relatively flat against the bed, when I heated the bed the center of the...
    Post by: jediknight0, Feb 25, 2016 in forum: Mods and Upgrades
  20. mark tomlinson
    Post

    Unresolved Z axis won't go down, only up

    Robo likely doesn't service the new ones :) The R1's are totally out of the picture. On the plus side they are not complicated electrically....
    Post by: mark tomlinson, Oct 31, 2023 in forum: Troubleshooting
Showing results 21 to 40 of 129 Next >
Search Again
Page 2 of 7