1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Allelujah
    Thread

    Solved Unidentified Part?

    Hello everyone. Its been about a year or two since i last been on the forums. So I been enjoying my Robo R1+ for the past 2 years now and I was...
    Thread by: Allelujah, Sep 8, 2018, 7 replies, in forum: Troubleshooting
  2. Allelujah
    Thread

    Answered Nozzle Replacement

    Hello everyone, I am back yet again with another few questions. So my new nozzles came in the mail today and I am eagerly waiting to install one...
    Thread by: Allelujah, Feb 4, 2017, 20 replies, in forum: General Questions
  3. Allelujah
    Thread

    Solved Types of Filament

    Hello everyone. Got another question for you all. Well a couple questions. First up is what are all the different types of filament can the Robo...
    Thread by: Allelujah, Jan 7, 2017, 2 replies, in forum: General Questions
  4. Allelujah
    Thread

    Smallest Detail

    Hello everyone and Happy New Years! So I woke up this morning with a question on my mind. What is the smallest level of detail the Robo R1+ can...
    Thread by: Allelujah, Jan 1, 2017, 22 replies, in forum: General Questions
  5. Allelujah
    Thread

    Custom Gunpla Sword

    Hello everyone! Finally got around to 3D printing one of my Gunpla sword designs. So as a first test to see if the handle would hold up, it did :D...
    Thread by: Allelujah, Dec 31, 2016, 5 replies, in forum: Show and Tell
  6. Allelujah
    Thread

    Solved Brittle Filament

    Hello everyone, another question that I got on the mind. So I been cursed with the brittle filament issue with Robo 3D's filament, or at least the...
    Thread by: Allelujah, Dec 26, 2016, 33 replies, in forum: General Questions
  7. Allelujah
    Thread

    Solved MatterControl + Fusion 360

    Hello everyone, I am back with another question. So I drew up some designs in Fusion 360 with specific measurements right? Well when I made the...
    Thread by: Allelujah, Dec 22, 2016, 5 replies, in forum: General Questions
  8. Allelujah
    Thread

    Allelujah's Project Dump

    Hell everyone! Today I am making a post where I share my project ideas/designs/things I like with you all. This post will be pic heavy of various...
    Thread by: Allelujah, Dec 21, 2016, 2 replies, in forum: Projects
  9. Allelujah
    Thread

    Medabots Blank Medal

    Hello everyone! I am so excited that I finally got my Robo R1+ fixed today that I was able to complete my first print. For those that have seen...
    Thread by: Allelujah, Dec 21, 2016, 12 replies, in forum: Show and Tell
  10. Allelujah
    Thread

    Solved Need help

    Hello everyone Im back with some more troubles today. So I think my hot end might be jammed/clogged. Im trying to feed filament in and it just...
    Thread by: Allelujah, Dec 19, 2016, 20 replies, in forum: Troubleshooting
  11. Allelujah
    Thread

    Another newbie question

    So I finally got my printer to work. Apparently i had a bad Z limit switch wire that wasn't connected and was epicly loose. Got that replace and...
    Thread by: Allelujah, Oct 8, 2016, 26 replies, in forum: General Questions
  12. Allelujah
    Thread

    Solved New Owner, got questions

    Hello I just received my printer today and I have ran into a few issues and questions. First off, Im going to attach some photos to help explain...
    Thread by: Allelujah, Sep 16, 2016, 8 replies, in forum: General Questions
Showing results 1 to 12 of 12
Search Again