1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Crypto3d
    Post

    Answered X axis pulley question

    I found this picture on the forums that shows two bearings as well (at least it looks that way to me) on someone else's printer:...
    Post by: Crypto3d, Sep 5, 2018 in forum: Troubleshooting
  2. Crypto3d
    Thread

    Answered X axis pulley question

    I have been having an issue with my prints shifting on the x axis. I believe it's due to either a loose motor gear, loose belt or the belt...
    Thread by: Crypto3d, Sep 5, 2018, 5 replies, in forum: Troubleshooting
  3. Crypto3d
    Post

    Raspberry pi config for Octoprint

    I have used the raspberry pi 3 without over clocking and I haven't had any problems. I just used the basic octoprint. Seems to work great.
    Post by: Crypto3d, Nov 21, 2017 in forum: General Questions
  4. Crypto3d
    Post

    Solved Abs or pla for extruder parts?

    Great to hear, thank you!
    Post by: Crypto3d, Nov 21, 2017 in forum: General Questions
  5. Crypto3d
    Thread

    Solved Abs or pla for extruder parts?

    I am planning on doing the dual fan upgrade and I have already printed the fan shrouds in pla. The instructions on thingiverse says they printed...
    Thread by: Crypto3d, Nov 20, 2017, 2 replies, in forum: General Questions
  6. Crypto3d
    Post

    Matter Control vs OctoPrint

    Success! After removing the global z offset and adjusting the start up gcode as recommended and then restarting matter control, I exported the...
    Post by: Crypto3d, Nov 8, 2017 in forum: Software
  7. Crypto3d
    Post

    Matter Control vs OctoPrint

    I'll get rid of the global offset and try this again tonight. Thanks!!!
    Post by: Crypto3d, Nov 6, 2017 in forum: Software
  8. Crypto3d
    Post

    Matter Control vs OctoPrint

    Thank u both for the suggestions. Other than the m565 command everything else was just what matter control put in there. I tried first putting...
    Post by: Crypto3d, Nov 6, 2017 in forum: Software
  9. Crypto3d
    Post

    Matter Control vs OctoPrint

    Well I added that to my startup gcode and it seems to have made no difference. You can see the M565 command in my gcode but the Matter control...
    Post by: Crypto3d, Nov 5, 2017 in forum: Software
  10. Crypto3d
    Post

    Matter Control vs OctoPrint

    Yeah I've been trying to switch over to cura but it seems to be doing some weird stuff too. I have another post about that if you have any...
    Post by: Crypto3d, Nov 4, 2017 in forum: Software
  11. Crypto3d
    Post

    Matter Control vs OctoPrint

    That makes sense. That was my first instinct but does that mean that matter control handles that on it's own when you are printing directly via...
    Post by: Crypto3d, Nov 4, 2017 in forum: Software
  12. Crypto3d
    Thread

    Matter Control vs OctoPrint

    For some reason I can print a model without problems when sliced and printed from Matter Control. But if I export the g-code to file and upload...
    Thread by: Crypto3d, Nov 4, 2017, 15 replies, in forum: Software
  13. Crypto3d
    Thread

    Slicing problem MAtterControl and Cura

    In the attached picture the chain link on the left was sliced and printed with matter control/matter slice. The one on the right was printed and...
    Thread by: Crypto3d, Nov 3, 2017, 2 replies, in forum: Software
  14. Crypto3d
    Post

    Solved Y axis movement

    Good call! The cable that goes to the heated bed was in the way. Thank you for pointing me in the right direction!
    Post by: Crypto3d, Oct 11, 2017 in forum: Troubleshooting
  15. Crypto3d
    Thread

    Solved Y axis movement

    Hi, I have an R1 that I recently purchased secondhand and refurbished myself. After replacing some damaged parts I'm getting some decent prints...
    Thread by: Crypto3d, Oct 10, 2017, 3 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again