1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. sawce_bause
    Thread

    cura not loading?

    I just upgraded my PC and trying to open cura. for some reason it installs with no problem but then when i try to open it i just get that small...
    Thread by: sawce_bause, Aug 22, 2021, 0 replies, in forum: Troubleshooting
  2. sawce_bause
    Post

    Bearings Problem

    getting some grinding noises from my Y axis bearings. can someone point me in the right direction for the thread ? since this whole process...
    Post by: sawce_bause, Nov 9, 2020 in forum: Troubleshooting
  3. sawce_bause
    Thread

    feeder gear removal, cleaning, replacement?

    during a print i noticed a clicking sound i noticed the "feeder gear" (sorry dont know the actual name of the part, see pic below ) slipping....
    Thread by: sawce_bause, Jan 3, 2019, 3 replies, in forum: Troubleshooting
  4. sawce_bause
    Post

    hardened nozzle recomendations

    ended up going with the e3dv6 as the micro swiss was out of stock. any tips on using a hardened steel nozzle? i noticed that i had to bump up my...
    Post by: sawce_bause, Sep 30, 2018 in forum: General Questions
  5. sawce_bause
    Thread

    hardened nozzle recomendations

    im looking at starting to print things using carbon fiber pla and other more abrasive printing plastics and need recommendations for a source or...
    Thread by: sawce_bause, Sep 20, 2018, 16 replies, in forum: General Questions
  6. sawce_bause
    Post

    Fusion 360 Trial ending

    You can renew the licence as a hobbyist yearly for free Sent from my Pixel 2 XL using Tapatalk
    Post by: sawce_bause, Sep 20, 2018 in forum: General Questions
  7. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    indeed backed it up in 4 different places just in case. you know the old saying " two is one, one is none";)
    Post by: sawce_bause, Aug 29, 2018 in forum: Troubleshooting
  8. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    got the new image yesterday afternoon from robert at robo support, and got a couple of test prints out of the way and it looks like everything is...
    Post by: sawce_bause, Aug 29, 2018 in forum: Troubleshooting
  9. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    thanks, looks like it might be a little over my head though. gonna see if robo support can just send me an image for my r2
    Post by: sawce_bause, Aug 27, 2018 in forum: Troubleshooting
  10. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    sorry you kinda lost me would i be changing the host name on the new micro sd via my pc or r2? is there an article on how to do this ? ...again...
    Post by: sawce_bause, Aug 27, 2018 in forum: Troubleshooting
  11. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    I just noticed the sticky in where an image of the r2's SD card is posted. Im an Uber newb when it comes to raspberry pi and Unix So can I just...
    Post by: sawce_bause, Aug 27, 2018 in forum: Troubleshooting
  12. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    Fingers crossed that it's just the image. Is there a limit on the capacity of micro SD? I noticed the preinstalled card is only 8 gb, and the...
    Post by: sawce_bause, Aug 27, 2018 in forum: Troubleshooting
  13. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    i couldnt control my printer at all with octoprint; it seemed like i could detect a printer since octoprint would pop up instead of "a this site...
    Post by: sawce_bause, Aug 26, 2018 in forum: Troubleshooting
  14. sawce_bause
    Post

    touchscreen stops responding along with octoprint

    doesnt seem like the frame is touching the screen. i finally just ended up flipping the power switch on the back as ive had my r2 sitting idle...
    Post by: sawce_bause, Aug 26, 2018 in forum: Troubleshooting
  15. sawce_bause
    Post

    R2 slipping for a specific spool of filament

    its very possible, you can also try to maybe draw out two or three feet from the spool and clip it off, could be just a section of it is bad and...
    Post by: sawce_bause, Aug 25, 2018 in forum: Troubleshooting
  16. sawce_bause
    Thread

    touchscreen stops responding along with octoprint

    after under a minute of turning on my r2 the touch screen becomes unresponsive. i can use the android app to control and print with the r2 when i...
    Thread by: sawce_bause, Aug 25, 2018, 19 replies, in forum: Troubleshooting
  17. sawce_bause
    Thread

    Printing w/o magnetic plate?

    I've been looking at a couple of vids and pics of people printing with their r2 and noticed that in a lot of them people print without the...
    Thread by: sawce_bause, Aug 24, 2018, 9 replies, in forum: General Questions
  18. sawce_bause
    Post

    motor problems? *video posted*

    since my r2 is still within the exchange period i ended up just taking it back to where i bought it from and ordered a complete replacement....
    Post by: sawce_bause, Aug 12, 2018 in forum: Troubleshooting
  19. sawce_bause
    Post

    motor problems? *video posted*

    the belts seem to have even tension except for the ones going to the motor, which feel super tight. which in my head makes sense since they are...
    Post by: sawce_bause, Aug 10, 2018 in forum: Troubleshooting
  20. sawce_bause
    Post

    motor problems? *video posted*

    i called in a favor and had a buddy of mine print me a set of the gantry aligning clips. i aligned the gantry as per instructions in robo3d's...
    Post by: sawce_bause, Aug 7, 2018 in forum: Troubleshooting
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2