1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Garnet
    Thread

    Unresolved Heating up and Shutting Down

    Hi, I just installed a new hot end. The unit heats up and once it reaches it's target temp the temps of the hot end and platform just start...
    Thread by: Garnet, May 17, 2021, 1 replies, in forum: Troubleshooting
  2. Garnet
    Post

    Hot End / Thermistor Replacement

    Thanks, new hot end ordered.
    Post by: Garnet, Apr 1, 2021 in forum: General Questions
  3. Garnet
    Post

    Hot End / Thermistor Replacement

    Thanks (although I'm guessing you mean 'can'). How likely is it that it's not the hot end but the thermistor or board that is the problem? Is...
    Post by: Garnet, Mar 31, 2021 in forum: General Questions
  4. Garnet
    Thread

    Hot End / Thermistor Replacement

    I've got an early Robo3D's and getting an extruder temp reading of 357.5* upon start up. Is there a way to know if the problem is the hot end or...
    Thread by: Garnet, Mar 31, 2021, 5 replies, in forum: General Questions
  5. Garnet
    Thread

    Unanswered Reperier Host: Extruder Temp Graph Limit

    Hi Does anyone know how to increase the temperature reading of the Extruder Temp Graph? I don't want to raise the temperature of the extruder,...
    Thread by: Garnet, Nov 6, 2016, 0 replies, in forum: General Questions
  6. Garnet
    Post

    Solved Robo3D won't respond/home

    Thanks very much for the suggestions, I rebooted, unplugged, etc. and it started working again. Cheer.
    Post by: Garnet, Sep 1, 2016 in forum: Troubleshooting
  7. Garnet
    Post

    Solved Robo3D won't respond/home

    It's just sitting there, no movement. It shows '1 Command Waiting' at the top. How do I export the terminal log? Thanks.
    Post by: Garnet, Aug 29, 2016 in forum: Troubleshooting
  8. Garnet
    Thread

    Solved Robo3D won't respond/home

    I've had my printer for a couple of years, been working well until this morning. I did the usual turn on, connect to Repetier, Home, but it won't...
    Thread by: Garnet, Aug 29, 2016, 6 replies, in forum: Troubleshooting
  9. Garnet
    Thread

    How to Stop Boogering?

    I'm getting a lot of boogers on my prints. I have been manually cleaning them, but sometimes miss and the extruder will hit a hardened booger and...
    Thread by: Garnet, Nov 6, 2014, 2 replies, in forum: Troubleshooting
  10. Garnet
    Thread

    Some layers delaminating

    I'm using a slight variation of the standard PLA print settings that Robo 3D specifies in their manual (slightly slower print speed to reduce...
    Thread by: Garnet, Oct 24, 2014, 3 replies, in forum: Troubleshooting
  11. Garnet
    Thread

    Slicer Settings

    I entered the settings posted in the thread below as I am wanting to get some higher quality prints:...
    Thread by: Garnet, Oct 10, 2014, 2 replies, in forum: Troubleshooting
  12. Garnet
    Thread

    Repetier Not Creating Support

    I have a small item with three short legs, so I just want support for the first 4 layers (there are some overhangs further up but they are...
    Thread by: Garnet, Jul 30, 2014, 5 replies, in forum: Troubleshooting
  13. Garnet
    Thread

    Extruder Heat Fluctuating

    My printer has been working fine, but in the last few prints I've tried (the same pieces it was printing just fine earlier) the extruder...
    Thread by: Garnet, Jul 26, 2014, 15 replies, in forum: Troubleshooting
  14. Garnet
    Thread

    Extruder Oozing Before Print

    The extruder oozes filament as it is heating up. I've set for three lines of skirt so I have time to pull it away which usually cleans the...
    Thread by: Garnet, Jul 25, 2014, 3 replies, in forum: Troubleshooting
  15. Garnet
    Thread

    Printing Very Small Items

    Hi, I have a part with a very small end point or tip (cylindrical shape, 5mm diameter x 8mm height) that melted in my last attempt. I'm going to...
    Thread by: Garnet, Jul 24, 2014, 5 replies, in forum: Troubleshooting
  16. Garnet
    Thread

    What's the Fan for? How to stop warping?

    The fan by the extruder is not always going on. Right now I'm printing a long flat item and not sure if it's supposed to be on or there's a wrong...
    Thread by: Garnet, Jul 18, 2014, 4 replies, in forum: Troubleshooting
Showing results 1 to 16 of 16
Search Again