1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Patrick Ryan

  1. Patrick Ryan
    Post

    Answered First layer imperfections!

    Ok, so your z offset may need to be raised. I would also ditch matter control and go with cura. I never had much luck with matter control Sent...
    Post by: Patrick Ryan, Aug 7, 2017 in forum: Troubleshooting
  2. Patrick Ryan
    Post

    Answered First layer imperfections!

    Well it looks like you have some areas that are under extruding and some areas that are over extruding. Check the tension on the filament make...
    Post by: Patrick Ryan, Aug 7, 2017 in forum: Troubleshooting
  3. Patrick Ryan
    Post

    Answered First layer imperfections!

    See of you can print just the first layer and take a picture while it's on the bed so I can get a better idea of what is happening. Sent from...
    Post by: Patrick Ryan, Aug 7, 2017 in forum: Troubleshooting
  4. Patrick Ryan
    Post

    Answered First layer imperfections!

    Gee-ont is that you? Are these surface imperfections on the first layer? Or the final layer? Sent from my SM-G930T using Tapatalk
    Post by: Patrick Ryan, Aug 7, 2017 in forum: Troubleshooting
  5. Patrick Ryan
    Post

    E3D Titan Aero combo announced

    You would do it through the gcode screen of your slicer Sent from my SM-G930T using Tapatalk
    Post by: Patrick Ryan, Jul 29, 2017 in forum: Off Topic
  6. Patrick Ryan
    Post

    E3D Titan Aero combo announced

    So, the steps per mm I have for the titan is 418.5. If it isn't any different after adjusting it then it sounds like the firmware isn't actually...
    Post by: Patrick Ryan, Jul 29, 2017 in forum: Off Topic
  7. Patrick Ryan
    Post

    Solved Upgraded to E3D V6 and filament is clumping

    Did you order it from a licensed e3d dealer? Sent from my SM-G930T using Tapatalk
    Post by: Patrick Ryan, Jun 30, 2017 in forum: Troubleshooting
  8. Patrick Ryan
    Post

    Titan Areo Upgrade Prusa Style

    Working on it now. I have updated the designs after finding a couple of problems. I should hopefully have it up and running in a couple weeks...
    Post by: Patrick Ryan, Jun 29, 2017 in forum: Mods and Upgrades
  9. Patrick Ryan
    Post

    Answered petg prints grinding filament

    Ok, I'll give that a shot. I might take the hot end apart to see if there is any debris in there, also. i have the e3dv6 and titan extruder...
    Post by: Patrick Ryan, Jun 19, 2017 in forum: Troubleshooting
  10. Patrick Ryan
    Post

    Answered petg prints grinding filament

    Oh and I'm not getting a lot of the gummy deposits that can occur with petg. The prints actually look decent
    Post by: Patrick Ryan, Jun 19, 2017 in forum: Troubleshooting
  11. Patrick Ryan
    Thread

    Answered petg prints grinding filament

    So after a month long issue of a shifting x axis I am now good on that but now I am having an issue with grinding the filament. It seems to happen...
    Thread by: Patrick Ryan, Jun 19, 2017, 3 replies, in forum: Troubleshooting
  12. Patrick Ryan
    Post

    Solved x axis missing steps/ layer shifting

    Well I think the drv8825 stepper drivers fixed it. or I was also having a neutral issue in my home electric and spent $1600 to replace my meter...
    Post by: Patrick Ryan, Jun 19, 2017 in forum: Troubleshooting
  13. Patrick Ryan
    Post

    Solved x axis missing steps/ layer shifting

    So I think the drv8825 drivers are working for me, mostly. I started a 16 hour print yesterday and after 10 hours everything was great. But...
    Post by: Patrick Ryan, Jun 10, 2017 in forum: Troubleshooting