1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. pclabtech
    Post

    "Disconnects" from the heat bed

    I saw Jerry a week ago, but my printer wasn't broke then :( I doubt they want to see me carrying in a broke printer.
    Post by: pclabtech, Jul 17, 2017 in forum: Software
  2. pclabtech
    Post

    "Disconnects" from the heat bed

    yep, the two left pins are pushed all the way down. So without doing a massive rewire using the magnets as connectors and void the warranty, I...
    Post by: pclabtech, Jul 17, 2017 in forum: Software
  3. pclabtech
    Post

    "Disconnects" from the heat bed

    Thanks! That's what it was... 2 of the pogo pins stuck down, I was able to pop them back up to get the bed to heat, but this is probably...
    Post by: pclabtech, Jul 17, 2017 in forum: Software
  4. pclabtech
    Thread

    "Disconnects" from the heat bed

    Ever since they updated my firmware, I have been getting The was an unhandled error while talking to the printer. Due to that OctoPrint...
    Thread by: pclabtech, Jul 16, 2017, 8 replies, in forum: Software
  5. pclabtech
    Post

    Power Supply Fan Whine

    I didn't want to "whine" about it because I figured I was just unlucky after about 2 weeks and it started making the bad sleeve / bearing...
    Post by: pclabtech, Jul 6, 2017 in forum: Troubleshooting
  6. pclabtech
    Thread

    Clean your R2 bed!

    Being new to PEI surfaces, I started experiencing failure after failure on something that should not lose adhesion, even with a raft. What I did...
    Thread by: pclabtech, Jun 26, 2017, 2 replies, in forum: Troubleshooting
  7. pclabtech
    Post

    R2 Stylus Holder

    That looks nice! I need to do one in matching colored plastic instead of the brown that I had loaded, but... I "semi blame" this print job for the...
    Post by: pclabtech, Jun 19, 2017 in forum: Show and Tell
  8. pclabtech
    Thread

    Stylus holder for the R2

    I put forth my best effort and CAD designing skills to make a stylus holder that clips to the door handle...
    Thread by: pclabtech, Jun 13, 2017, 0 replies, in forum: Mods and Upgrades
  9. pclabtech
    Post

    My Youtube video of my R2 in action

    Added another youtube video. I am guessing they fixed timelapse as my latest creations actually recorded... Here is a screw and a nut. [MEDIA]
    Post by: pclabtech, Jun 11, 2017 in forum: Show and Tell
  10. pclabtech
    Post

    First epic fail

    Here is what the horse should have looked like: [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: pclabtech, Jun 11, 2017 in forum: Show and Tell
  11. pclabtech
    Post

    R2 Heated Bed Design

    This comes from the official "Documentation" that was posted earlier: Cleaning the print bed surface The Robo R2 print bed surface is a sheet of...
    Post by: pclabtech, Jun 11, 2017 in forum: Show and Tell
  12. pclabtech
    Thread

    First epic fail

    I woke up to "not a horse" as the base broke from the build plate. [ATTACH]
    Thread by: pclabtech, Jun 10, 2017, 3 replies, in forum: Show and Tell
  13. pclabtech
    Post

    Robo R2 Overhang Tests

    That looks really nice. I will try printing one with .1mm but all I have is Cura so no fancy settings to tweak my output.
    Post by: pclabtech, Jun 9, 2017 in forum: Show and Tell
  14. pclabtech
    Post

    Stress testing using "Ready for Battle" Figure

    It "was" going to be 10 hours 42 minutes, but I changed the layer from .1mm to .2mm per layer resolution to reduce plastic use and time to 5 hours...
    Post by: pclabtech, Jun 9, 2017 in forum: Show and Tell
  15. pclabtech
    Post

    Stress testing using "Ready for Battle" Figure

    Ok here it is![ATTACH]
    Post by: pclabtech, Jun 9, 2017 in forum: Show and Tell
  16. pclabtech
    Post

    Stress testing using "Ready for Battle" Figure

    The printer is initializing now :) We shall see...
    Post by: pclabtech, Jun 8, 2017 in forum: Show and Tell
  17. pclabtech
    Thread

    Stress testing using "Ready for Battle" Figure

    Here is some pictures of a print job I never ran on my original Robo or my R1 due to me being too afraid it would not do this piece justice. Here...
    Thread by: pclabtech, Jun 8, 2017, 8 replies, in forum: Show and Tell
  18. pclabtech
    Post

    Cura 2.5 fails after install

    Yes, anti viruses (Like Symantec, and also windows defender) marked Robo's Cura 2.5 as a "Reputation" virus (which only means the software version...
    Post by: pclabtech, Jun 8, 2017 in forum: General Questions
  19. pclabtech
    Post

    Robo R2 Print Tests

    Also check the fine tuning of the Z axis. In the old days people would smash the plastic into the surface but I find with this printer, you don't...
    Post by: pclabtech, Jun 8, 2017 in forum: Show and Tell
  20. pclabtech
    Post

    Robo's OctoPrint

    I had been wondering this as well. Robo sent an update to the printer via WiFi through my firewall and router, which means any hack with tools...
    Post by: pclabtech, Jun 7, 2017 in forum: Software
Showing results 1 to 20 of 44 Next >
Search Again
Page 1 of 3