1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. cosber
    Post

    Solved Brittle Filament

    I've had problems with brittle filament but discovered it's usually only the first foot or so. I just bend the filament until it stops breaking.
    Post by: cosber, Dec 27, 2016 in forum: General Questions
  2. cosber
    Thread

    Star Trek Enterprise

    Took a small version of the Enterprise from Thingiverse: http://www.thingiverse.com/thing:64937 I scaled it up to 1:350 because it seemed most of...
    Thread by: cosber, Nov 30, 2016, 2 replies, in forum: Show and Tell
  3. cosber
    Post

    Unresolved Quick release screw won't unscrew

    Give them one more chance. You're having one of those bad luck experiences. You'll be happy with it once you get one that works!
    Post by: cosber, Nov 25, 2016 in forum: Troubleshooting
  4. cosber
    Post

    Unresolved Quick release screw won't unscrew

    But can you unloosen the screw?:rolleyes:
    Post by: cosber, Nov 25, 2016 in forum: Troubleshooting
  5. cosber
    Post

    Unresolved Quick release screw won't unscrew

    I also had the same problem with overtightened screw. I feared I was going to strip the screw head, and as I am fortunate to live in San Diego...
    Post by: cosber, Nov 11, 2016 in forum: Troubleshooting
  6. cosber
    Post

    Solved Removing Hotend on R1+

    Don't scrape it off. After looking at pictures, I found I was putting it back in with the wiring on the left side. When I figured out the wire...
    Post by: cosber, Oct 27, 2016 in forum: Troubleshooting
  7. cosber
    Post

    Solved Removing Hotend on R1+

    I was surprised to see Brian heat up the end and still grab the piece. Only the nozzle and I guess the block just above is all that gets hot.
    Post by: cosber, Oct 26, 2016 in forum: Troubleshooting
  8. cosber
    Post

    Solved Removing Hotend on R1+

    I had just gone to Robo shop because I had a jam and the screw that holds it was so tight I couldn't unscrew it. I was told that there was a batch...
    Post by: cosber, Oct 26, 2016 in forum: Troubleshooting
  9. cosber
    Post

    Solved Removing Hotend on R1+

    When you say "a little muscle", where do I apply it. I also cannot get it back in. It looks like it needs to go up a hair so the swing plate will...
    Post by: cosber, Oct 26, 2016 in forum: Troubleshooting
  10. cosber
    Thread

    Solved Shout Out To Robo3D

    Wasn't sure which forum to post this, so since I had problems with my printer I put it here. As a Kickstarter alumni and an idiot, I had lots of...
    Thread by: cosber, Oct 3, 2016, 0 replies, in forum: Troubleshooting
  11. cosber
    Post

    Unanswered Having trouble with first layers

    Mine is doing that also. My printer was dialed in for over a year, not having to do any adjustments, it was like heaven. Then one print the...
    Post by: cosber, Sep 21, 2016 in forum: Troubleshooting
  12. cosber
    Post

    Yet another Kickstarter/crowdfunding cattle call

    I know nothing about business, but couldn't simply be a matter of, why pay for it out of my pocket when I can get someone else to come up with the...
    Post by: cosber, Sep 10, 2016 in forum: Off Topic
  13. cosber
    Post

    Discovery from 2001

    Here are the better shots. [ATTACH]
    Post by: cosber, Sep 10, 2016 in forum: Show and Tell
  14. cosber
    Post

    Discovery from 2001

    I considered it but decided to put in on a shelf in my home theater. I'm leaving the ceiling for the Enterprise that is waiting for me to create...
    Post by: cosber, Sep 10, 2016 in forum: Show and Tell
  15. cosber
    Post

    Discovery from 2001

    http://www.thingiverse.com/thing:950664 I scaled it up 125% because the bigger the better. I was going to go 150% but the sphere itself would have...
    Post by: cosber, Sep 10, 2016 in forum: Show and Tell
  16. cosber
    Thread

    Discovery from 2001

    [ATTACH] From a model posted in Thingiverse. A beautiful piece with incredible detail that Robo handled beautifully. Excuse the photo quality....
    Thread by: cosber, Sep 10, 2016, 7 replies, in forum: Show and Tell
  17. cosber
    Post

    Show us your best Robo 3d print

    I don't mean to denigrate your work, but is this the type of quality I can expect from a hand held scanner? There is no definition in the faces....
    Post by: cosber, May 23, 2016 in forum: Projects
  18. cosber
    Post

    First test of FLEKS 3D build plate kit

    How long ago did you write them? I haven't heard a thing. It's been exactly a month. I guess I'll try again.
    Post by: cosber, May 23, 2016 in forum: Show and Tell
  19. cosber
    Post

    Simplify 3d

    After having consistently successful prints with PLA, suddenly I couldn't get a good first layer. It was driving me crazy since I was finally...
    Post by: cosber, May 11, 2016 in forum: Software
  20. cosber
    Post

    First test of FLEKS 3D build plate kit

    I purchased the plate a couple weeks ago, haven't had a chance to use it yet, but when I opened the package, the plates were slightly scratched...
    Post by: cosber, Apr 23, 2016 in forum: Show and Tell
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2