1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jaykav99
    Post

    Does a smaller nozzle guarantee better details?

    Gotcha, thanks for the reply and tip on speed settings
    Post by: Jaykav99, May 8, 2018 in forum: Off Topic
  2. Jaykav99
    Thread

    Does a smaller nozzle guarantee better details?

    Possibly kind of a newb question but I've been printing awhile now and have stuck with the 0.4 diameter nozzles. And now i am getting into objects...
    Thread by: Jaykav99, May 8, 2018, 6 replies, in forum: Off Topic
  3. Jaykav99
    Thread

    List of material types

    Hey guys is there an official list somewhere that robo says the R2 works with or at least tested with. Store page just says 30+
    Thread by: Jaykav99, Aug 27, 2017, 9 replies, in forum: General Questions
  4. Jaykav99
    Post

    Filament pulling failure during print.

    Good there is model correction options out there, as for my machine its 100% clogged now. Can not remotely manually push any filament through,...
    Post by: Jaykav99, Jul 23, 2017 in forum: Troubleshooting
  5. Jaykav99
    Post

    Failed Thor Hammer Steel print, but wow it was going well. Pics inside

    He just replied confirming the link I sent...Same exact one you said...My main concern was overall fitment but I'm good now. So thank you very...
    Post by: Jaykav99, Jul 22, 2017 in forum: Show and Tell
  6. Jaykav99
    Post

    Failed Thor Hammer Steel print, but wow it was going well. Pics inside

    I actually found him from a post he put on here talking bout nozzles. Sent him a message double-checking a few things but that is prob the exact...
    Post by: Jaykav99, Jul 22, 2017 in forum: Show and Tell
  7. Jaykav99
    Post

    Failed Thor Hammer Steel print, but wow it was going well. Pics inside

    I didnt for this print but will be upgrading to one before I attempt again.
    Post by: Jaykav99, Jul 22, 2017 in forum: Show and Tell
  8. Jaykav99
    Thread

    Failed Thor Hammer Steel print, but wow it was going well. Pics inside

    So basically the filament appeared to snap and then clogged my extruder, sucks but what can you do...it was about 25%(4hrs) done or so and the...
    Thread by: Jaykav99, Jul 22, 2017, 7 replies, in forum: Show and Tell
  9. Jaykav99
    Post

    Filament pulling failure during print.

    Well that sucked...after walking through something with jerry, it seems over all that some part of the filament got messed up or broken off...
    Post by: Jaykav99, Jul 19, 2017 in forum: Troubleshooting
  10. Jaykav99
    Thread

    Filament pulling failure during print.

    Was about 20 % through printing benchy...and then i heard a sound dadadadadadadadadadada then i noticed the wheels aren't spinning at all to pull...
    Thread by: Jaykav99, Jul 19, 2017, 7 replies, in forum: Troubleshooting
  11. Jaykav99
    Post

    Over all Speed Settings

    Sounds like a good rule of thumb to follow...thanks alot.
    Post by: Jaykav99, Jul 17, 2017 in forum: General Questions
  12. Jaykav99
    Thread

    Over all Speed Settings

    I know this must be a broad question but what would be a typical safe print speed for the R2. I have the R1+ right now and would hope I can take...
    Thread by: Jaykav99, Jul 17, 2017, 4 replies, in forum: General Questions
  13. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Doug, yesterday i just fixed the broken tape area and my latest print was tons better. Still a bit off so i may still have some issues but still...
    Post by: Jaykav99, Apr 11, 2017 in forum: Troubleshooting
  14. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Well it certainly could have been worse problem i guess... but looks like ill be hitting the store today...thanks again for your time Geof.
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  15. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Ok decided to come home for lunch...impatient man i am. But i think i might have found a culprit. Bed cable is still in its bracket...dont see any...
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  16. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Great thank you very much for your time so far. I will def get into it tonight to see what's up and let you know
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  17. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Geof one more thing I just remembered. Sometimes when the bed moves. Its gets to the max move distance and it makes a loud noise like it's...
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  18. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Wow ok thanks for all or this useful info. I will check it out, when I get home tonight.
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  19. Jaykav99
    Post

    Solved Printing goes off axis mid print

    Whichever axis is used for the bed moving back and forth. I've only had the printer a few weeks but it also my first printer . I will check out...
    Post by: Jaykav99, Apr 10, 2017 in forum: Troubleshooting
  20. Jaykav99
    Thread

    Solved Printing goes off axis mid print

    This might be a slicer issue over all but. I was printing a music box out and as it layed down the first layer everything is good. Then second...
    Thread by: Jaykav99, Apr 10, 2017, 15 replies, in forum: Troubleshooting
Showing results 1 to 20 of 20
Search Again