1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 4
  1. DavidR
    Thread

    Hard Bounds on Cura slicer settings

    I am new to printing in general and am humbled by the enormous number of settings I can tweak. I was wondering what the extremes (i.e. the...
    Thread by: DavidR, Jan 17, 2018, 13 replies, in forum: General Questions
  2. DavidR
    Thread

    boiling looking print

    What is the culprit here? This happens relatively frequently where I will have this "boiling" appearance on my prints.
    Thread by: DavidR, Jan 16, 2018, 1 replies, in forum: Troubleshooting
  3. DavidR
    Post

    belt tensioning

    @Geof Ok. You'll have to zoom in. I think this may be the problem, the little ring sticking out from the white frame is flush against the wall...
    Post by: DavidR, Jan 14, 2018 in forum: Troubleshooting
  4. DavidR
    Post

    belt tensioning

    @Geof Also, this may be relevant, if I am standing directly in front and looking down from above, the right side of the uppermost 8mm rod closest...
    Post by: DavidR, Jan 14, 2018 in forum: Troubleshooting
  5. DavidR
    Post

    belt tensioning

    @Geof Interesting. Ok, I am fairly new to this. I was reading a book on 3d printing maintenance and it said that after awhile one needs to adjust...
    Post by: DavidR, Jan 14, 2018 in forum: Troubleshooting
  6. DavidR
    Thread

    belt tensioning

    My belts are broken in. I bought a spring loaded belt tensioner but I can't seem to find anywhere to put it where it wont cause problems. At best...
    Thread by: DavidR, Jan 14, 2018, 7 replies, in forum: Troubleshooting
  7. DavidR
    Thread

    Greasing 6mm rods

    The guide mentions that the included grease can be used in place of white lithium grease for greasing the Z-axis screw. It is mum as to whether...
    Thread by: DavidR, Jan 14, 2018, 1 replies, in forum: General Questions
  8. DavidR
    Thread

    Solved Issue with thin prints

    Imagine you are printing a vertical pencil. I am having the following issue with prints like this, about halfway up the printer starts to layer...
    Thread by: DavidR, Jan 8, 2018, 2 replies, in forum: Troubleshooting
  9. DavidR
    Post

    Bed Calibration Wizard

    @Geof Thanks! What I did was switch to advanced mode and I compared the corner that I felt was iffy to the other three. For all but the front left...
    Post by: DavidR, Jan 8, 2018 in forum: General Questions
  10. DavidR
    Post

    Bed Calibration Wizard

    @WheresWaldo They did for the Z-offset Wizard. It doesn't appear to cover the "bed calibration wizard". In particular, when it says "Adjust the...
    Post by: DavidR, Jan 8, 2018 in forum: General Questions
  11. DavidR
    Post

    Bed Calibration Wizard

    @WheresWaldo Sorry I should have been more clear with my question. I know what the tool is and how to use it for the Z-offset wizard. I am running...
    Post by: DavidR, Jan 8, 2018 in forum: General Questions
  12. DavidR
    Thread

    Bed Calibration Wizard

    I am running this wizard in guided mode. It is telling me to use the Z-offset Tool to level the printer and I have no idea what this means. I...
    Thread by: DavidR, Jan 8, 2018, 10 replies, in forum: General Questions
  13. DavidR
    Post

    overextrusion during pre-print sequence

    @WheresWaldo Thank you for your reply! I take it your are referring to the following section. I'm assuming I can put a semicolon in front to...
    Post by: DavidR, Jan 6, 2018 in forum: Troubleshooting
  14. DavidR
    Thread

    overextrusion during pre-print sequence

    During the pre-print sequence (I'm not sure what this is actually called-- the sequence of movements where the bed and extruder go up and down and...
    Thread by: DavidR, Jan 6, 2018, 3 replies, in forum: Troubleshooting
  15. DavidR
    Post

    WebCam Issue

    I am actually having this same issue, but the start stream/refresh technique does not work. I know I have the URL correct because it works on the...
    Post by: DavidR, Jan 6, 2018 in forum: Troubleshooting
  16. DavidR
    Post

    firmware upgrade

    Ah ok. Thanks so much!
    Post by: DavidR, Jan 5, 2018 in forum: Software
  17. DavidR
    Post

    firmware upgrade

    I don't have a super strong comp sci background. I had thought the firmware and the OS updates were different. The manual seems to distinguish...
    Post by: DavidR, Jan 5, 2018 in forum: Software
  18. DavidR
    Thread

    firmware upgrade

    I have received an R2 for Christmas. I have updated the OS; I am curious as to whether or not I should have the current firmware release already...
    Thread by: DavidR, Jan 5, 2018, 4 replies, in forum: Software
Find older messages
Showing results 61 to 78 of 78
Search Again
Page 4 of 4