1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 7
  1. Lance Weston
    Post

    Making auto leveling and/or mesh leveling work

    About a year ago I posted how to modify the firmware to make mesh leveling work. I set the mesh to 6x6 and watched it go through it's paces...
    Post by: Lance Weston, Feb 25, 2024 in forum: Troubleshooting
  2. P.L.A.STIC-Fantastic
    Post

    Unanswered Z-Axis Fun -- Problem Out Of Box

    Alright. When it arrived right out of the box, brass nuts for the Z-axis drive were disengaged, the auto-level was hanging off of both sides and...
    Post by: P.L.A.STIC-Fantastic, Feb 28, 2016 in forum: Troubleshooting
  3. Toro1966
    Post

    Unanswered First print with PLA - Help with settings.

    Mark - Going to check that out this evening. I noticed that after the perimeter was put down, it did not print the objects in the middle, but...
    Post by: Toro1966, Jul 18, 2016 in forum: Troubleshooting
  4. ammulder
    Post

    Auto bed leveling malfunction robo c2

    I'm also having leveling issues. When I print a 2"x2" piece in the center of the bed, it works fine (z offset -5.4). When I print four 2"x2"...
    Post by: ammulder, Feb 4, 2017 in forum: Troubleshooting
  5. tkoco
    Post

    Print Bed Leveling Issue

    I contacted the Robo 3D support about the bed. The beds are manufactured using nylon. Injection molded nylon is deemed a high shrinkage plastic...
    Post by: tkoco, Apr 13, 2019 in forum: Troubleshooting
  6. joea
    Post

    Unanswered Where to set Marlin offset from -X limit for proper "home" position

    The end stop seems to work properly. The problem is moves slightly off the stop, just as Y does, and holds there. Y is right on the Y0 mark...
    Post by: joea, Mar 18, 2023 in forum: Troubleshooting
  7. KenO
    Post

    Head crashing with Probe Failure error, fixed I think

    In my case the LED turns itself off at the center location during the auto leveling process prior to doing a print and or running "Fine Tune...
    Post by: KenO, Mar 26, 2018 in forum: Troubleshooting
  8. Element18592
    Post

    Partially Solved Robo 3D R1 Level on Some parts of the bed?

    Thats actually one of the first things i did, i forgot to mention it in the original post. When i increased it, it allowed it to print yes, but it...
    Post by: Element18592, Mar 15, 2016 in forum: Troubleshooting
  9. robert albrecht
    Post

    Unanswered Not extruding during print.

    Sorry major Duh moment you want me to mark the actual filament it's self.. if I did this right it looks like it only extracted 75 mm of filament....
    Post by: robert albrecht, Sep 27, 2020 in forum: Troubleshooting
  10. I Need Help
    Post

    Unresolved Homing on Z axis is inconsistent

    Hello, Recently I have had some trouble properly homing the z axis on my ROBO 3D R1+. When I enter G28 into the gcode terminal the extruder of...
    Post by: I Need Help, Apr 4, 2016 in forum: Troubleshooting
  11. MindTorque
    Post

    Solved Possible minor Z-axis issue?

    Greetings and felicitations! My new Robo3D arrived yesterday, so far it seems quite impressive although there may be a bit of a Z-axis issue. My...
    Post by: MindTorque, Jun 2, 2016 in forum: Troubleshooting
  12. Perry Genovese
    Post

    Solved Terribly Inconsistent Printer!

    to get my bed level was a nightmare. I use a depth gage on my digital caliper. I use the horizontal rod of the x-axis with the bed centered...
    Post by: Perry Genovese, Feb 22, 2017 in forum: Troubleshooting
  13. mark tomlinson
    Post

    Unanswered Not extruding during print.

    So move the extruder to the center of the bed, have it in the air -- off the bed. Find a reference point for the filament above the extruder......
    Post by: mark tomlinson, Sep 27, 2020 in forum: Troubleshooting
  14. robert albrecht
    Post

    Unanswered Not extruding during print.

    Could I make a mark on one of the side vertical support arms and measure that? Sent from my Phone 2 using Tapatalk
    Post by: robert albrecht, Sep 27, 2020 in forum: Troubleshooting
  15. daniel871
    Post

    Unresolved Rear Right Corner of Bed Has Prints Not Adhering

    The shortest explanation I can give you is to tell you to raise the extruder up to about 180mm from the bed, then pick the glass up and look at...
    Post by: daniel871, Mar 23, 2017 in forum: Troubleshooting
  16. mark tomlinson
    Post

    Partially Solved Bed level / uneven printing

    Autoleveling as defined in the version of Marlin used by the R1 and R1+ does not work correctly if the X axis (left to right as you look at the...
    Post by: mark tomlinson, Aug 9, 2017 in forum: Troubleshooting
  17. WheresWaldo
    Post

    Marlin for the R2 - UBL Enabled

    Working on Marlin 1.1.7 (released 15 DEC 2017) for the R2. Just getting ready to test a few things. Lots of small bug fixes to UBL and some new...
    Post by: WheresWaldo, Dec 16, 2017 in forum: Mods and Upgrades
  18. Teacher Kelly
    Post

    Hotend Not Heating (Replaced Nozzle, Plugged and Replugged)

    Update: I should have posted back in April when I first started trying to fix this thing. As soon as I posted, I noticed one more wire in the top...
    Post by: Teacher Kelly, Sep 23, 2023 in forum: Troubleshooting
  19. jim3Dbot
    Post

    Understanding the MK2A PCB HeatBed, R1 swaparoo

    Hello Greg.........Thanks for the comment...........Adding another 1/8" of insulation will definitely help, but if you check with an IR...
    Post by: jim3Dbot, Sep 1, 2016 in forum: Mods and Upgrades
  20. hybridman
    Post

    Solved Z axis problems

    I was hoping some of you seasoned users can help me out- really frustrated. Using my Robo-3D R1+ Matter Control 5.1 I have printed a part that...
    Post by: hybridman, Nov 28, 2017 in forum: Troubleshooting
Showing results 61 to 80 of 129 Next >
Search Again
Page 4 of 7