1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Nathan Elverud
    Thread

    Partial Answer Does the Robo3D R1 Plus use a real arduino or a clone?

    I am almost certain I accidentally bent the usb port on my printer by putting it up higher and the weight of the cable bent it. It clearly has a...
    Thread by: Nathan Elverud, Apr 21, 2017, 3 replies, in forum: Troubleshooting
  2. Nathan Elverud
    Thread

    Partial Answer Been having bad luck with filament. What brand should I buy?

    It seems like half the filament I buy prints poorly. What brand should I buy?
    Thread by: Nathan Elverud, Apr 20, 2017, 3 replies, in forum: Troubleshooting
  3. Nathan Elverud
    Thread

    Solved Print head pushes into bed on first layer.

    I cannot get the printer to print at the correct height. Every time, it pushes itself against the bed allowing no filament to come out.
    Thread by: Nathan Elverud, Mar 6, 2017, 5 replies, in forum: Troubleshooting
  4. Nathan Elverud
    Thread

    Answered Soaking nozzle overnight in acetone. Good or bad idea?

    My nozzle has a pla everywhere. In and outside and even the threads are dirty. Would letting the nozzle soak in a small bowl of acetone do any...
    Thread by: Nathan Elverud, Feb 26, 2017, 3 replies, in forum: Troubleshooting
  5. Nathan Elverud
    Thread

    Solved Huge jam in heat break.

    I got a jam and ended up making it worse trying to fix it and now I've got plastic almost completely filling the heartbreak. I've got the extruder...
    Thread by: Nathan Elverud, Feb 23, 2017, 1 replies, in forum: Troubleshooting
  6. Nathan Elverud
    Thread

    Answered Says temperature dropped too much when it actually didn't

    Why I try to print, I get this message as soon as it hits the x end stop. Error:Extruder switched off. Temperature fell too much during print! It...
    Thread by: Nathan Elverud, Feb 4, 2017, 5 replies, in forum: Troubleshooting
  7. Nathan Elverud
    Thread

    Unresolved My fans are cooling my hot end.

    I have an e3d v6 hotend and for some reason it's getting cooled down by my fans. I'm using two fans with this shroud...
    Thread by: Nathan Elverud, Jan 30, 2017, 8 replies, in forum: Troubleshooting
  8. Nathan Elverud
    Thread

    Partially Solved Bad print quality

    When I first got my Robo, the plastic it came with pretty very well and the next black pla plastic I got printed very well too. Since then I've...
    Thread by: Nathan Elverud, Jan 26, 2017, 8 replies, in forum: Troubleshooting
  9. Nathan Elverud
    Thread

    Solved X limit switch not working right

    I just finished replacing my x carriage for a cable chain mod and now my x axis is screwed up. When I try G28 X, it moves a tiny bit and then it...
    Thread by: Nathan Elverud, Jan 23, 2017, 3 replies, in forum: Troubleshooting
  10. Nathan Elverud
    Thread

    How do I replace the thermistor?

    I bought an R1+ a week ago and think I shorted the thermistor this morning trying to remove a jam. I've been looking at buying RioBrand 100Kohm...
    Thread by: Nathan Elverud, Dec 22, 2016, 1 replies, in forum: Mods and Upgrades
Showing results 1 to 10 of 10
Search Again