1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Omegagundam
    Post

    Printer error Bed not heating up

    Ok kewl ill do that. Thank you!
    Post by: Omegagundam, Nov 19, 2017 in forum: Troubleshooting
  2. Omegagundam
    Thread

    Printer error Bed not heating up

    Hello All My bed for the R2 isn't heating up Not sure what to do. I took a pic of the error on the screen and the pogos thank you [ATTACH]...
    Thread by: Omegagundam, Nov 19, 2017, 33 replies, in forum: Troubleshooting
  3. Omegagundam
    Post

    Need a better program for my R2

    ok looks like i can add image....
    Post by: Omegagundam, Nov 5, 2017 in forum: General Questions
  4. Omegagundam
    Thread

    Need a better program for my R2

    Hello everyone. I have the R2 and i am hesitant to use it anymore because of Cura. I don't like how it makes the supports to where under the print...
    Thread by: Omegagundam, Nov 5, 2017, 14 replies, in forum: General Questions
  5. Omegagundam
    Thread

    R2 filament motor stops working after 2-3 layers

    Hello all I had my R2 working great last night until what i was printing poped off the bed. So this morning i tried to do it again but this time...
    Thread by: Omegagundam, Jun 3, 2017, 1 replies, in forum: Troubleshooting
  6. Omegagundam
    Thread

    Cura 2.5 for R2...

    Hello all I have the R2 and finally got cura to connect to printer. but i am having issues trying to change the temperature settings. i tried to...
    Thread by: Omegagundam, Jun 2, 2017, 2 replies, in forum: Software
  7. Omegagundam
    Post

    Unresolved Print starts to blob up

    Thank you guys! I can make 2 and do 2 at a time. I do have blender so i can easily duplicate it.
    Post by: Omegagundam, Mar 31, 2017 in forum: Troubleshooting
  8. Omegagundam
    Thread

    Unresolved Print starts to blob up

    Hello all i have the robo 3d r1 printer i am using pla with nozzle at 190 degrees. after a little while the plastic starts to get into a big...
    Thread by: Omegagundam, Mar 31, 2017, 4 replies, in forum: Troubleshooting
  9. Omegagundam
    Post

    Unanswered Stepper Motor for extuder not moving.

    Hello Mark i just ran into a few new problems i took out the driver off the mother board for the extruder and i had put it back in and it works...
    Post by: Omegagundam, Mar 22, 2017 in forum: Troubleshooting
  10. Omegagundam
    Post

    Unanswered Stepper Motor for extuder not moving.

    Kewl thank you Mark! ill try and get one to see if it will fix the issue
    Post by: Omegagundam, Mar 11, 2017 in forum: Troubleshooting
  11. Omegagundam
    Thread

    Unanswered Stepper Motor for extuder not moving.

    Hello All, My extruder stepper motor does not seem to want to spin. when i try to advance it i feel vibration but wont spin. I made sure the...
    Thread by: Omegagundam, Mar 11, 2017, 5 replies, in forum: Troubleshooting
  12. Omegagundam
    Thread

    Support material or no suport material

    Hello everyone I am wondering if i should have the support material on as i print or just leave it off. when i print my items with support...
    Thread by: Omegagundam, Nov 3, 2014, 8 replies, in forum: Troubleshooting
  13. Omegagundam
    Thread

    Issue cloging jamming/ filament crimping bending on the top part of the extruder

    Hello all I am noe having an issue with my ABS filament going town into the extruder printing for 20 minutes then it stops coming out. I unloosen...
    Thread by: Omegagundam, Oct 19, 2014, 13 replies, in forum: Troubleshooting
  14. Omegagundam
    Thread

    Got Printer working now my prints come out messed up a bit..

    I was able to get my printer calibrated right Now my problem is that my prints are not soo nice. this is what the left bracket that i am printing...
    Thread by: Omegagundam, Oct 5, 2014, 12 replies, in forum: Troubleshooting
  15. Omegagundam
    Thread

    brand new robo 3d printer and first attempt to print it gets clogged

    Hello all please forgive my ignorance. I have just bought a printer and had finally set it up. i wanted to do my first test print using the blue...
    Thread by: Omegagundam, Oct 1, 2014, 7 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again