1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 3 of 266
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. AkiraSieghart

    Answered Weird problems with using PETG with my Robo R1+

    AkiraSieghart, Nov 25, 2018
    Replies:
    2
    Views:
    104
    AkiraSieghart
    AkiraSieghart
    Nov 26, 2018
  2. howdyrichard

    Answered Are these still available?

    howdyrichard, Nov 25, 2018
    Replies:
    1
    Views:
    67
    mark tomlinson
    mark tomlinson
    Nov 25, 2018
  3. Saor_Alba
    Locked

    Solved Printing Same Project Constantly

    Saor_Alba, Nov 25, 2018
    Replies:
    2
    Views:
    74
    Saor_Alba
    Saor_Alba
    Nov 25, 2018
  4. howdyrichard

    Answered Is the Hot-end hot enough?

    howdyrichard, Nov 25, 2018
    Replies:
    1
    Views:
    64
    mark tomlinson
    mark tomlinson
    Nov 25, 2018
  5. DRas

    Answered R1+ intermittent print failures

    DRas, Nov 22, 2018
    Replies:
    5
    Views:
    108
    DRas
    DRas
    Nov 23, 2018
  6. Qaytin

    Answered Concave print

    Qaytin, Nov 22, 2018
    Replies:
    1
    Views:
    77
    WheresWaldo
    WheresWaldo
    Nov 23, 2018
  7. Laura Kapp
    Locked

    Solved Prints Failing - Need Help Understanding Why

    Laura Kapp, Apr 8, 2018
    Replies:
    16
    Views:
    287
    WheresWaldo
    WheresWaldo
    Nov 22, 2018
  8. John in MS

    Solved Is there an diagram on how the R1 extruder is assembled?

    John in MS, Nov 4, 2018
    Replies:
    9
    Views:
    181
    mark tomlinson
    mark tomlinson
    Nov 22, 2018
  9. JeremyL

    Solved Autoleveling Robo3d

    JeremyL, Nov 19, 2018
    Replies:
    5
    Views:
    113
    mark tomlinson
    mark tomlinson
    Nov 20, 2018
  10. Victoria Nedbal

    Answered Top layer/Infill Issues

    Victoria Nedbal, Nov 19, 2018
    Replies:
    2
    Views:
    82
    mark tomlinson
    mark tomlinson
    Nov 19, 2018
  11. AkiraSieghart

    Answered Cracked my bed on my R1 Plus

    AkiraSieghart, Nov 11, 2018
    Replies:
    3
    Views:
    141
    BrooklynBay
    BrooklynBay
    Nov 18, 2018
  12. Me-Again

    Answered Invalid Printer Response

    Me-Again, Nov 17, 2018
    Replies:
    3
    Views:
    92
    mark tomlinson
    mark tomlinson
    Nov 17, 2018
  13. Tommie Kalb

    Partially Solved My y axis is acting horribly

    Tommie Kalb, Nov 15, 2018
    Replies:
    14
    Views:
    187
    Tommie Kalb
    Tommie Kalb
    Nov 16, 2018
  14. Erin-Ellen Winfree

    Partial Answer R1+ Bed Not Heating

    Erin-Ellen Winfree, Nov 2, 2018 ... 2 3
    Replies:
    53
    Views:
    609
    mark tomlinson
    mark tomlinson
    Nov 15, 2018
  15. 4sfaloth

    Answered Chunk of glass bed came off

    4sfaloth, Nov 11, 2018
    Replies:
    16
    Views:
    250
    mark tomlinson
    mark tomlinson
    Nov 14, 2018
  16. gunsmoke132

    Answered robo 3d r1+ heated bed getting no volts form the ramps board port

    gunsmoke132, Nov 11, 2018
    Replies:
    2
    Views:
    93
    mark tomlinson
    mark tomlinson
    Nov 12, 2018
  17. Kyle McElroy

    Solved Thank you to Mark Tomlinson & Where's Waldo

    Kyle McElroy, Nov 9, 2018
    Replies:
    0
    Views:
    82
    Kyle McElroy
    Kyle McElroy
    Nov 9, 2018
  18. Esteban Carrera
    Locked

    Answered Printer Hardware Error M999

    Esteban Carrera, Jul 3, 2016 ... 2
    Replies:
    23
    Views:
    1,856
    mark tomlinson
    mark tomlinson
    Nov 8, 2018
  19. Victoria Nedbal

    Answered Need New Thermistor for Robo R1 +

    Victoria Nedbal, Nov 7, 2018
    Replies:
    1
    Views:
    102
    mark tomlinson
    mark tomlinson
    Nov 7, 2018
  20. Mr Wire

    Solved extruder cable came off

    Mr Wire, Nov 6, 2018
    Replies:
    3
    Views:
    104
    Mr Wire
    Mr Wire
    Nov 6, 2018
Showing threads 41 to 60 of 5,313

Thread Display Options

Loading...
Page 3 of 266